Cenmate 3-bay enclosure backplate for 80mm PWM fan (freeCAD)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Backplate replaces original 70 mm x 15 mm fan with a Noctua NF-A8 (80 mm x 25 mm) and adds a knob to set the fan speed.
- Rating
- 0 / 5
- Likes
- 1
- Downloads
- 3
- Makes
- 0
- Views
- 30
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Electronics
- License
- GNU General Public License v2.0
Cenmate 3-bay enclosure backplate for 80 mm Noctua fan
Replacement backplate for the Cenmate 3-bay 3.5" HDD enclosure. It replaces the original 70 mm x 15 mm fan with a Noctua NF-A8 PWM (80 mm x 25 mm) and adds a knob to set the fan speed.
Why
The stock 70 mm fan is whiny. A series resistor helped a little, but not enough.
The enclosure only has a 2-wire fan supply, so there is no PWM control of the fan.
With the NF-A8 and a small PWM speed controller the enclosure is quieter even at full speed, and whisper quiet at about 1/3 of max.
Results
Disk temperatures, three drives:
Old 70 mm fan: 36 / 45 / 41 C
NF-A8 at about 1/3 speed: 31 / 39 / 36 C
And that leaves roughly 2/3 of the fan speed in reserve

Parts
1x printed backplate (CEN-backplate-005-backplate.stl)
1x Noctua NF-A8 PWM, 80 x 80 x 25 mm
4x Noctua NA-AV1 anti-vibration mounts (come with the fan)
1x PWM fan speed controller with potentiometer and knob (eBay, sold as "12V PWM fan speed controller / governor"; 12 V input, 4-pin fan output)
Original rocker power switch and the original backplate screws from the enclosure
Design features
Outer size 131 x 105 mm, same screw pattern as the original plate (holes sized 3.32 mm).
Inner lip that locates the plate in the enclosure body, with small tolerance ribs. I reduced them next to nothing since they were interfering with screw alignment. Fits well now on second print.
82 mm fan socket, recessed so the 25 mm deep fan fits inside the enclosure.
Holes for the NA-AV1 mounts instead of screws.
Cutout for the original ON/OFF rocker switch.
Hole for the speed controller potentiometer, with a pocket for the board on the inside.
Opening for the enclosure's rear ports (USB-C, USB-A, DC jack).
There is a recess on one side of the fan socket to accomodate at least the first fold of the noctua fan wire - which is fairly long.
Design is not fully parametric, I did not have time for that in this one-off project. Variables and proper part names are used less and less towards the project tip. The good part is that the STL file derived from this freecad file is working well. Small adjustments - for example if you are fixing the fan in place with screws should not be difficult.
Printing
Printed in PLA on a Prusa MK4, 0.4 mm nozzle, 0.2 mm layers.
Print time around 4 hours.
Print it flat, outer face down. Supports for port recess - organic.
Check that the lip fits in the enclosure before final assembly; tweak the tolerance in the FreeCAD file if needed. I actually started printing just a 2mm thick backplate with the lip and screw holes to check alignment.
Wiring
Original 2-wire fan lead -> speed controller power input (12 V). The fan governor wires soldered to the fan connector wires (the original fan cut off).
Speed controller 4-pin output -> NF-A8 PWM connector.
The controller has a small trimmer for the start (minimum) speed. Set it so the fan starts reliably at the lowest knob position. I did not need to tweak it at all.
Assembly
Fit the rocker switch into its cutout.
Mount the speed controller and fix the potentiometer with its nut.
Mount the fan with the NA-AV1 mounts (see below).
Connect the wiring, route fold the cables. They have enough space, but I also added a ziptie to hold together 2 upper folds of the Noctua cable together with the speed governor wire. This aligns nicely by the side of the fan.
The bottom of the regulator board cannot touch the metallic surface of the enclosure, but nevertheless I put a piece of standard insulation tape on it prior to inserting the regulator into it's socket. I think you can see it on photo 6.
Screw the plate onto the enclosure with the original screws.
Maybe it is worth noting that I tested the fan and the regulator with a 12 V power supply prior and during the assembly. It is reassuring to know that all things work before you put them together. Although the design is very simple and it is hard to imagine what could go wrong.
Inserting the NA-AV1 mounts (the fiddly part)
The NA-AV1 mounts are hard to pull through the plate. The skirt just before the final stopper does not want to go through the hole, and pulling on the rubber tip alone mostly stretches the mount and I was afraid it might tear it. Holes were pretty standard for computer fan mounting screws. If I made the 3rd print, I might enlarge those from 4.9 mm to 6.2 mm. But still this system should not be such a pita.
What worked for me:
Make a loop or two using the long end clockwise of thick, strong thread around the mount just behind the inner skirt in the groove before the final stopper.
Feed the tip of the mount and the thread ends (leave the pull end fairly long) and while pushing-pulling the mount pull the long thread counterclockwise through the hole in the plate. It helped to get that skirt firmly in place with a few attempts.
Pull on the thread and the tip together. The thread drags the skirt through the hole.
Once the skirt pops through, you will remove the thread. I just continued to pull.
Repeat for all four corners. Then install the fan - where the mounts also do not click immediately. But once they did - it was ok.

Files
CEN-backplate-005-backplate.stl - print file
CEN-backplate-005.FCStd - FreeCAD source
The FreeCAD model is a single PartDesign body. The main dimensions are in a VarSet (plate size, lip size and thickness, fan socket size, fan recess, screw hole size), so it is adaptable to other fans or even enclosure variants.