3D Slot-Together Christmas Ornaments - Star, Tree, Bauble, Bell, Print Flat, No Glue
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Flat-printed Christmas ornaments that slot together into 3D shapes: bauble, bell, star and tree, no glue.
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 3
- Makes
- 0
- Views
- 16
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Home Decor
- License
- Creative Commons — Attribution — Noncommercial
Flat to print, 3D on the tree. Each ornament is two flat halves that slide into each other at 90° and click in place: a star, a tree, a bauble and a bell. They print in minutes, need no supports and no glue, and look great in two colours, for example a gold half and a red half.
What you get. Four ornaments, each made of half A (slot from the top) and half B (slot from the bottom, with the hanging loop). Built, they are 79 to 82 mm tall including the loop and 61 to 76 mm wide: star 76 × 79 mm, tree 61 × 82 mm, bauble 69 × 82 mm, bell 64 × 79 mm. The cut-outs catch the light of the tree lights. The loop has a 4.4 mm hole for a thread or a hook.
Why it prints well. Flat print, 2.4 mm thick, no supports. The slot has 0.2 mm clearance per side, a 0.4 mm lead-in at the entry and a 0.4 mm chamfer on the first layer against elephant foot. The tips next to the slots are trimmed, so there are no thin slivers. Two small ribs in the slot of half B click into a window in half A, so A does not slide off when the ornament hangs by the loop on B.
Colours. Each half is a separate file, so you can mix them: gold and red, green and gold, silver and blue, white and red. The pictures show some combinations. One colour works too.
IN THE FILES
star-A-gold,star-B-gold: star halves (76.1 × 68–79 mm, 2.4 mm thick)tree-A-green,tree-B-green: tree halves (60.8 × 71–82 mm)bauble-A-red,bauble-B-red: bauble halves (68.8 × 71–82 mm)bell-A-gold,bell-B-gold: bell halves (64.0 × 69–79 mm)slot_3d_ornaments.scad: the parametric source. You can change the size (60 to 100 mm), the plate thickness and the slot fit.
PRINT SETTINGS: PLA, 0.20 mm layers, 3 walls, 100 % infill (the parts are 2.4 mm thick), no supports, flat on the bed. All 8 halves fit one 250 mm plate, or print in two batches of 4 halves on a small bed (two ornaments per batch). Silk gold, red and green PLA look festive.
ASSEMBLY: Hold half B with the loop up. Slide half A from below into the slot of B, crossing the halves at 90°, until the two ribs in the slot snap into the window in A. Hang the ornament by the loop on B.
Honest notes:
The hanging loop on the tree is the thinnest spot, about 1 mm wide where it meets the tip. It is fine for hanging, but do not bend it sideways.
The images are 3D renders made from the same files you print. This set has not been test-printed yet.
What we checked numerically on the exported STL files: every half is a closed single solid; fully assembled, the halves of all four ornaments do not overlap; moving A down by 1 mm from the assembled position runs into the ribs of B, so A is held when the ornament hangs by B; upwards A rests against the end of the slot in B; nothing is thinner than 0.8 mm.
The ribs press 0.1 mm into A, so how firm the click is depends on your printer. If it is too tight, sand the ribs lightly; if it is loose, a drop of glue is the fallback.
The design is original: no licensed characters, no brands.
SLICED (Bambu Lab P2S, 0.20 mm, PLA, 3MF included):
gold: 21.0 g, about 36 min
green: 8.7 g, about 17 min
red: 16.2 g, about 26 min