BeanDock – Illy 250 g Can Adapter for De'Longhi Magnifica Evo
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Screw an Illy 250 g bean can on upside down and feed beans into your Magnifica Evo. Slide or rotary gate. PETG.
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 0
- Makes
- 0
- Views
- 25
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Kitchen
- License
- Creative Commons — Attribution — Noncommercial — NoDerivatives
Screw an Illy 250 g bean can on upside down and let the beans feed straight into the grinder. A built-in gate seals the chute, so you can swap cans without spilling a single bean.
BeanDock replaces the hopper lid of the De'Longhi Magnifica Evo. The can sits inverted on top of the machine, the beans drop into the hopper by gravity as you brew, and when the can is empty you close the gate, unscrew it and put the next one on.
Choose your gate
Every set is the lid + one gate option. Both options use the same lid and the same Illy screw thread.
Option A — Slide gate (recommended first print)
A flat paddle slides through the socket: pull it out to open, push it in to close.
BeanDock_Lid.stl
BeanDock_A_SocketBase.stl
BeanDock_A_Funnel.stl
BeanDock_A_Slide.stl
The socket is split into two parts so that every part prints flat, with no bridges over the slide channel.
Option B — Rotary dial
A 120° lever turns a sealing disc on an off-centre pivot.
Click detents hold the lever firmly at OPEN and at CLOSED.
A window in the lever shows an engraved "OPEN" on the base only when the gate is open.
The funnel sits on a wide support shelf, so the can stands solid.
BeanDock_Lid.stl
BeanDock_B_RotaryBase.stl
BeanDock_B_RotaryDisc.stl
BeanDock_B_RotaryFunnel.stl
Compatibility
Machine: De'Longhi Magnifica Evo — tested on the ECAM290.61. Other Magnifica Evo models with the same hopper recess should fit; please check before printing the lid.
Can: Illy 250 g whole-bean can with the standard Illy screw lid.
Printer: the lid is about 211 × 177 mm, so you need a bed of at least 220 × 220 mm.
Print settings
Material: PETG (choose a food-contact filament if you want it in contact with beans)
Nozzle / layer: 0.4 mm / 0.2 mm
Walls / infill: 3 walls, 20–30 % gyroid
Filament: roughly 200 g for a full set
Tested on: Creality K2 Plus, textured PEI plate
Lid: top face down on the plate, no supports
A_SocketBase / B_RotaryBase: spigot on the plate, supports from build plate only (under the flange)
A_Funnel / B_RotaryFunnel: flat base down, mouth up, no supports — a brim helps
A_Slide / B_RotaryDisc: flat, no supports
All files are exported in their print orientation.
Assembly
Option A — Slide gate
Lay the slide in the channel of the socket base.
Put the funnel on top; the two pins line it up.
Glue with a drop of gel super glue on the pins only — never on the slide.
Option B — Rotary dial
Drop the disc onto the pivot pin of the base.
Lower the funnel so both pins go into their bosses.
Glue with gel super glue only inside the two bosses, on top of the support post and on the outer half of the shelf. Keep glue away from the disc so it stays free to turn.
Turn the lever: you should feel a click at OPEN and at CLOSED.
Both options
Fit the lid in place of the original hopper lid.
Twist the socket assembly into the lid until the bayonet stops.
Screw the inverted Illy can onto the thread.
To change can: close the gate, unscrew, screw on the next one, open.
Credits
The Illy can thread is remixed from "Illy Can Connector" by mart_sch (Thingiverse, CC BY 4.0). Lid, socket, funnels, slide gate, rotary gate and the overall design are by 3DWARD.
"Illy", "De'Longhi" and "Magnifica Evo" are trademarks of their respective owners. BeanDock is an unofficial, compatible accessory and is not made, affiliated with or endorsed by illycaffè or De'Longhi. The names are used only to say what it fits.
