1 / 1
LOW D DOUBLE WHISTLE - Pentatonic Melody + Drone — image 1

LOW D DOUBLE WHISTLE - Pentatonic Melody + Drone

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Low D double whistle: one pipe plays a D major pentatonic melody, the other holds a steady Low D drone underneath.

Rating
0 / 5
Likes
0
Downloads
2
Makes
0
Views
19
Reviews
0

Updated at source:

Model information

Category
Music
License
Creative Commons — Attribution — Noncommercial — Share Alike

LOW D DOUBLE WHISTLE - Pentatonic Melody + Drone

=================================================

A Low D double whistle: one pipe plays a D major pentatonic melody

(D E F# A B), the other holds a steady Low D drone underneath. Both

pipes are fed from one Y-forked mouthpiece, with a thin septum at the

lips that splits your breath in half, one half per pipe.

It is the big brother of my Alto G double whistle (model 1852148),

scaled up to Low D. It is made for slow playing and listening to the

harmonies over the drone rather than for fast tunes. Stay in the first

octave: blowing harder for the second octave pushes the drone up too.

Licence: CC BY-NC-SA. STL files only.

PARTS

-----

Print one of each unless stated:

LowD_Dual_Fork.stl Y-forked mouthpiece (both pipes)

LowD_UpperBody.stl x2 plain upper tube, one per pipe

LowD_Dual_Middle_Melody.stl middle section, 2 finger holes

LowD_Dual_Middle_Drone.stl middle section, no holes

LowD_Dual_Bottom_Melody.stl bottom section, 2 finger holes

LowD_Dual_Bottom_Drone.stl bottom section, no holes

LowD_Foot.stl x2 plain foot, one per pipe

Each pipe, from the mouthpiece down:

Melody: Fork -> UpperBody -> Middle_Melody -> Bottom_Melody -> Foot

Drone: Fork -> UpperBody -> Middle_Drone -> Bottom_Drone -> Foot

PRINTING

--------

- PLA, 25% infill is plenty.

- Body tubes (UpperBody, Middle, Bottom, Foot): print VERTICALLY, tenon

down. The joint clearances were tuned on vertical prints. Round

sockets printed lying down tend to sag and come out undersized.

- The fork needs supports - see below.

SUPPORTS - PLEASE READ

----------------------

The forked mouthpiece cannot be printed without supports in any

orientation, and cleaning them off takes time. Tree/organic supports

with a slightly larger top Z distance (around 0.2-0.25mm) come away

more easily.

Clean the outside however you like, but take care around the two

windows. The labium edges (the sharp edges inside the windows) must

stay clean and undamaged, and no support material may be left inside

the windways or the throat. Slide a strip of card through each

windway, and look down each socket towards the light, before

assembling. A pipe that won't speak, or only squeaks, almost always

has debris in its windway or a damaged labium.

WHICH SIDE THE MELODY GOES ON

-----------------------------

The two branches of the fork are designed to be identical, so in

theory either side can take the melody pipe.

On my print they are not quite equal: the melody plays properly when

fitted on the RIGHT-hand branch (the player's right, holding the

whistle to play). Fitted on the left, the melody sounds weak.

I put this down to my print and support clean-up rather than the

design - most likely a little leftover material or slight damage in

one windway. Your print may favour the other side, or neither.

Try the melody on both sides and keep whichever sounds stronger.

ASSEMBLY AND JOINT FIT

----------------------

- The UpperBody tubes may be loose in the fork's sockets (mine were,

probably because the fork prints at a different orientation to a

single head). A wrap or two of PTFE tape on the tenon fixes it.

- Same for any other joint that is loose: PTFE tape. Airtight matters

more than tight. A leaking joint makes notes weak or unstable.

- Don't glue anything until the whistle has been played and tuned.

TUNING

------

Both pipes sound Low D with all holes covered. Two pipes on the same

note will always beat slightly against each other; a little beating

gives the sound some life.

If the beating is more than you like, use the drone's taped

UpperBody joint as a tuning slide: pull it out a little to lower the

drone, push it in to raise it. Adjust by ear against the melody's

bottom D.

The melody's A and B may sit a few cents flat, because two holes of

the full whistle were left out to make it pentatonic. This is accepted

- it's an instrument for harmonies, not for tuning-meter accuracy.

FINGERING (melody pipe)

-----------------------

Holes numbered 1-4 from the mouthpiece. X = covered, O = open.

Note 1 2 3 4

D X X X X

E X X X O

F# X X O O

A X O O O

B O O O O

Every note works against the D drone, so there are no wrong notes -

just wander and listen.

Tags