Shearwater Peregrine & TX Bumper - Keep Calm
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Snap-on TPU bumper for the Shearwater Peregrine and Peregrine TX with KEEP CALM / BREATHE DEEP in the bezel.
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 0
- Makes
- 0
- Views
- 6
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Outdoor Sports
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
A one-piece TPU bumper for the Shearwater Peregrine TX. It covers the sides and the edge of the face and leaves the screen and the back open. The computer goes in from the back of the bumper until two snap tongues click behind the step on the sides of the case. The wrist strap or bungee stays on the computer. The bezel says KEEP CALM above the screen and BREATHE DEEP below it, in green TPU inlaid flush with the face.
Made for my Peregrine TX. Shearwater lists the same 77 × 68 × 25 mm case for the Peregrine and the Peregrine TX, so it should fit both, but I only have the TX.
Print-tested: v6 printed in black and green TPU for AMS and fits my Peregrine TX snugly. Not dive-tested yet.
Update (v6): the inside is 0.4 mm smaller than v5 and the hooks are 1 mm deeper. v5 fitted, but I wanted it tighter and holding harder.
Fit rings (plate 2): printers and TPU differ a little, and a bumper has to be snug. Plate 2 has three thin rings with the bumper's inside outline at 99.5 %, 100 % and 100.5 % (1, 2 and 3 dots on top). Print them first (about 28 min and 7.3 g on a P2S, slicer estimate), then push them over your computer. The ring that goes on with a light stretch and no play is your scale: print the bumper plate at the same scale in the slicer. The 100 % ring is the bumper's inside outline, and my v6 bumper is printed at 100 %. I have not printed the 99.5 % and 100.5 % rings myself.
80.2 × 64.8 × 18.2 mm. Inside 74.3 × 58.9 mm with R7.3 corners, sized on my Peregrine TX with printed test rings and bumpers: a 75.1 × 59.7 mm ring sat on it without play, a 74.7 × 59.3 mm bumper (v5) fitted but I wanted it tighter, so v6 is 0.4 mm smaller again
Wall 2.94 mm (7 lines), lip over the face 2.12 mm, window 62 × 44 mm R6 with a 1.0 mm chamfer. Outer edges rounded: R3 on the face side (turning into 45° at the plate, so the first layers do not hang), R1.5 at the back
Two snap tongues, one on each long side, 12 mm wide and 1.26 mm thick, cut free by two slits. Each ends in a hook that stands 2.0 mm proud of the inside wall and catches the step on the side of the case. The tongue tip runs 2 mm past the back edge to give the hook a long 45° lead-in
Arches over the MENU and FUNC buttons on both ends and over the sensor port
No hole in the lip for the SHEARWATER badge: there is a hidden 0.8 mm recess under the lip instead
Lettering: my own bold capitals, 6.6 mm tall, 1.5 mm strokes, at least 1.4 mm between letters, inlaid 0.68 mm deep (the first 4 layers) and flush with the face. I printed three lettering options on test strips first (PETG letters in TPU, PETG letters in a PETG face, TPU letters in TPU): TPU in TPU came out cleanest, and it bonds to the body
The back is open, so the computer can go on its charger with the bumper on (not tested yet)
Prints lip face down without supports. All wall thicknesses are multiples of the 0.42 mm line width. Exact CAD (B-rep) with real fillets, no stepped mesh
About 1 h 07 min and 15.3 g on a P2S at 0.16 mm (5 filament changes; slicer estimate)
Print settings: Bambu Lab P2S, 0.4 mm nozzle, 0.16 mm High Quality, 2 walls, 15% infill, no supports, smooth PEI plate (the face takes the plate's finish). Filament 1 is the body in Bambu TPU for AMS (black), filament 2 the lettering in TPU for AMS (green).
Files: 3MF (Bambu Studio project, P2S 0.16 profile, two filaments; plate 1 the bumper, plate 2 the fit rings), STL for the body, the lettering (already flipped for printing) and the three fit rings, STEP (body and lettering as separate solids).
Photos: my v5 print on my Peregrine TX, the inside with the snap tongues, and the front. v6 looks the same from the outside; inside, its hooks are bigger and the tongue tips stick out 2 mm at the back. Renders: the back of v6 and the fit rings.
