Cressi Leonardo Bumper - Do You Have Backup?
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Snap-on TPU bumper for the Cressi Leonardo dive computer with DO YOU HAVE BACKUP? inlaid in the bezel.
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 0
- Makes
- 0
- Views
- 8
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Outdoor Sports
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
A one-piece TPU bumper for the Cressi Leonardo. It covers the bezel and the sides and leaves the screen, the button and the back open. The computer goes in from the back of the bumper until four claw tongues at 3 and 9 o'clock click behind the 45° step on the sides of the case. The wrist strap stays on the computer. Above the screen it asks DO YOU HAVE BACKUP? in green TPU inlaid flush with the face.
Made for my Cressi Leonardo. I have not tried it on other models.
Print-tested: printed in black and green TPU for AMS and fitted on my Cressi Leonardo (see photos). Not dive-tested yet.
Ø 73.1 × 20.9 mm. Inside Ø 66.4 mm all the way down. The bezel is about 66.8 mm (checked with printed test rings), so the bumper sits on it with 0.4 mm of stretch. An earlier version was wider below the bezel and could turn on the computer, so this one keeps 66.4 mm along the whole depth
Wall 3.36 mm (8 lines), lip over the face 2.12 mm, window Ø 50 mm with a 0.8 mm chamfer and a cut-out shaped around the button (18.9 × 10.4 mm). Outer edges rounded: R3 on the face side (turning into 45° at the plate, so the first layers do not hang), R1.5 at the back
Grip: two claws at 3 and 9 o'clock, 90° from the button, each 65 mm wide and split by a slit into two 32 mm tongues, so they flex like short narrow ones. Each claw starts 16 mm from the face and turns inward at 45° by 3 mm (2.1 mm thick) with 0.3 mm preload, so it pulls the bumper against the bezel. 30° lead-in at the bottom. Between the claws the wall ends 15.5 mm from the face, before the strap
Put it on slowly: the tongues bend across the print layers, and Bambu's datasheet gives TPU for AMS only 31 % elongation across layers (over 650 % along them)
Lettering: my own bold capitals, 6.6 mm tall, 1.5 mm strokes, at least 1.4 mm between letters, inlaid 0.68 mm deep (the first 4 layers) and flush with the face
Prints face down without supports. All wall thicknesses are multiples of the 0.42 mm line width. Exact CAD (B-rep) with real fillets, no stepped mesh
My print took 1 h 09 min on a P2S at 0.16 mm and used 15.8 g (14.9 g black, 0.9 g green; 5 filament changes)
Print settings: Bambu Lab P2S, 0.4 mm nozzle, 0.16 mm High Quality, 2 walls, 15% infill, no supports, smooth PEI plate (the face takes the plate's finish). Filament 1 is the body in Bambu TPU for AMS (black), filament 2 the lettering in TPU for AMS (green).
Files: 3MF (Bambu Studio project, P2S 0.16 profile, two filaments), STL for the body and the lettering (already flipped for printing), STEP (body and lettering as separate solids).
Photos: my print on my Cressi Leonardo, the front, and the inside with the four claw tongues.
