1 / 3
Case for ESP32-S31-Korvo-1 — image 1
1 / 3

Case for ESP32-S31-Korvo-1

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Case for the Espressif ESP32-S31-Korvo-1 V1.1 with its 4.3" LCD subboard mounted.

Rating
0 / 5
Likes
0
Downloads
0
Makes
0
Views
7
Reviews
0

Updated at source:

Model information

Category
Electronics
License
Apache License 2.0

ESP32-S31-Korvo-1 case with 4.3" LCD

A case for the Espressif [ESP32-S31-Korvo-1 V1.1](https://docs.espressif.com/projects/esp-dev-kits/en/latest/esp32s31/esp32-s31-korvo-1/user_guide.html) with its 4.3" LCD subboard mounted. Outer size is 112.3 × 102.0 × 24.6 mm. No heat inserts are needed, and every screw is countersunk and sits flush, front and back.

## Features

  • LCD window, with the glass recessed 0.6 mm behind the bezel face

  • Openings for USB-A, both USB-C ports, power switch, microSD, camera, two microphones, RGB LED and two speaker cables

  • Printed plungers for all six buttons. SET, MODE, VOL− and VOL+ stand 1 mm proud. RESET and BOOT sit 1 mm recessed, so you press them with a pen tip

  • The board drops straight in. The port slots are open at the top and closed by tongues on the bezel

Print settings

STL files are already in print orientation. No supports needed.

File

Qty

Orientation

print_shell.stl

1

back down

print_bezel.stl

1

face down

print_button_long_x4.stl

4

foot down

print_button_short_x2.stl

2

foot down

  • Designed for a 0.4 mm nozzle (2.4 mm walls, 2.0 mm floor)

  • The only bridges are the microSD window (18 mm), the speaker cable holes (8 mm) and the nut trap ceilings (about 6 mm)

  • A test print with a 0.5 mm nozzle and 100% infill worked without supports

  • Optional: the short buttons keep RESET and BOOT recessed so they don't get pressed by accident. If you'd rather press them with a finger, use long buttons there too (six long, no short). Both types fit the same holes.

Hardware

Qty

Part

Use

4

M3×10 countersunk

back → shell → main board → board standoffs

4

M3×25 countersunk

front → bezel → shell column → nut

4

M3 hex nut

in the traps in the back of the shell

M3×20 will technically fit instead of M3×25, but the hex nut well may be tricky to print because the nuts might not fall in deep enough.

Assembly

  1. Remove the four screws on the back of the main board. Leave the standoffs and the LCD subboard in place.

  2. Lower the board stack into the shell, port side first.

  3. Fasten it from the back with the four M3×10 screws into the standoffs.

  4. Drop the six plungers onto their switches (long: bottom row, short: next to the camera).

  5. Fit the bezel and fasten it with the four M3×25 screws. Push a nut into each trap in the back.

Known compromises

  • The top bezel screws are asymmetric (left corner and mid-top) because the camera tab occupies the top-right corner. That corner is held by the bezel tongues only

  • The mid-top screw and nut sit about 5 mm from the antenna tip, which may affect RF slightly

  • The microSD card sits about 6 mm behind the top wall. Use a fingernail or tweezers

Links

Source files:
https://github.com/ByteWelder/Case-for-ESP32-S31-Korvo-1

Tags