1 / 13
D-Sub Connector Hood v2, long – DE9 to DD50 (9 to 50 pins), closed with cable ties — image 1
1 / 13

D-Sub Connector Hood v2, long – DE9 to DD50 (9 to 50 pins), closed with cable ties

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Version 2, longer: two-part printable backshell for solder-cup D-Sub connectors, 9 to 50 pins, closed with cable ties.

Rating
0 / 5
Likes
0
Downloads
8
Makes
0
Views
19
Reviews
0

Updated at source:

Model information

Category
Electronics
License
Creative Commons — Attribution

This is version 2 (longer, five sizes) of my D-Sub Connector Hood – DE9 / DA15 / DB25, published as a remix of it. Version 1 (shorter, three sizes) stays online unchanged.

What's new in version 2

  • Two new sizes: DB37 (DC37) and DD50 (three rows, thicker shell).

  • Longer hood and wider cable channel. With every pin of a large connector in use, version 1 did not leave enough room behind the solder cups, and the DB25 channel (7 mm) was too small for 25 wires. The hoods are now 5 to 6 mm longer, the cable channel grows to 6.3 / 8 / 10.5 / 11.5 / 13.7 mm, and the wires get a short straight run after the heat shrink before they bend towards the exit (at most 45 degrees).

  • The head of the neck tie now sits in a pocket on the side of the neck (like the ear ties), because the bigger channel leaves too little wall on top.

  • Version 1 (shorter, DE9 / DA15 / DB25) stays available as its own model and in the source: --kurz.

What it is

A two-part printable hood (backshell) for D-Sub connectors with solder cups, in five sizes: DE9 (often called DB9), DA15, DB25, DB37 and DD50. It fits on a connector you have already soldered. The two shells are held together by cable ties instead of screws: one tie around each ear and one around the neck at the cable exit. A fourth tie inside the hood acts as strain relief. The ties sit in grooves just below the surface, so nothing sticks out except the tie heads, which rest in pockets.

The flange of the connector sits in a slot, the D stays free at the front, and both mounting holes stay usable (room for 4.8 mm hex standoffs / jack screws of the mating connector). It works with plugs (male) and sockets (female).

What you need per hood

  • 2 printed shells (top and bottom)

  • 4 cable ties, 2.5 mm wide, 100 to 200 mm long (3 to close the hood, 1 inside as strain relief)

  • optional: heat shrink tubing for the solder cups

No screws, nuts or glue.

Sizes

Size

Outer size W x H x L

Cable channel

Clamp ribs

Intended cable

DE9 (DB9)

34.4 x 16.2 x 38.5 mm

6.3 mm

5.5 mm

up to 9 wires AWG 24, or a round cable up to 6.3 mm

DA15

42.7 x 16.2 x 40.0 mm

8.0 mm

7.2 mm

up to 15 wires AWG 24, or a round cable up to 8 mm

DB25

56.6 x 16.2 x 44.0 mm

10.5 mm

9.7 mm

up to 25 wires AWG 24, or a round cable up to 10.5 mm

DB37

72.9 x 17.2 x 49.3 mm

11.5 mm

10.7 mm

up to 37 wires AWG 24, or a round cable up to 11.5 mm

DD50

70.5 x 19.4 x 49.0 mm

13.7 mm

12.9 mm

up to 50 wires AWG 24, or a round cable up to 13.7 mm

Wire count assumes AWG 24 (0.25 mm²) with PVC insulation, about 1.4 mm thick; with all pins in use the bundle fills about half of the channel. For a different cable, change the channel diameter in the CadQuery source (see below).

Print settings

  • Material: PETG (PLA should work too, but is untested)

  • Nozzle 0.4 mm, layer height 0.15 mm

  • No supports. Print each shell with its outer face on the bed and the parting face up, exactly as oriented in the STL files.

  • Printed with the stock PrusaSlicer profile "0.15mm SPEED" for the Prusa CORE One (2 perimeters, 15 % infill). The 3MF files contain this profile and both shells of one size on a single plate.

  • Estimated time and filament for both shells (PrusaSlicer 2.9.6): DE9 28 min / 8.0 g, DA15 31 min / 9.3 g, DB25 35 min / 11.5 g, DB37 45 min / 15.6 g, DD50 47 min / 16.3 g

Tip: print one bottom shell first and lay the connector flange into the slot. It should sit without clamping and without rattling.

Assembly

  1. Insulate the solder cups (heat shrink), bundle the wires.

  2. Lay the connector with its flange into the slot of the bottom shell and lead the wires through the cable channel.

  3. Close the strain-relief tie around the bundle inside the chamber in front of the rear wall, then cut it short. If you pull the cable, this tie stops against the wall.

  4. Put the top shell on. The small collars on the top shell fit into pockets in the bottom shell and align both halves.

  5. On each side, push a tie from the top through the slot in the ear, lead it out underneath, up along the narrow side, and into its head. Put the head into the pocket of the top shell, pull tight and cut flush.

  6. Put the third tie around the neck, head in the pocket on the side of the top shell, pull tight and cut flush.

Opening

Cut the three outer ties at the head with side cutters, not at the hood. Use new ties to close it again, or releasable ties of the same width if their head fits the pocket.

Notes and assumptions

  • Designed for standard 2.5 mm cable ties: band about 1.05 mm thick, head about 5.0 x 4.2 x 3.4 mm. If your ties are thicker than 1.2 mm or the head is wider than 4.6 mm, adjust the parameters in the source and regenerate.

  • Connector geometry follows the standard dimensions of MIL-DTL-24308. The fit was checked in CAD for plug and socket, each with the mating connector fully inserted and 4.8 mm standoffs. Solder-cup length varies between makers; the hood leaves room for cups up to about 10 mm behind the front of the flange, plus 5 mm of heat shrink and a straight run of the wires behind it.

  • The cable ties are what hold the hood together. It is meant for cables at a desk or inside equipment, not as a load-bearing part.

Print status (honest)

  • Version 2 (this model) has not been printed yet. The fit of all five sizes was checked in CAD (plug and socket, mating connector with standoffs, wire path for every pin, wall thickness). The photos show version 1.

  • Version 1 (original model): all three sizes were printed in Prusament PETG on a Prusa CORE One, 0.15 mm SPEED profile, without supports.

  • DB25: assembled with a soldered socket, wires and cable ties (photos 1, 2 and 4).

  • DE9: shells printed and fitted together (photo 3). An earlier DE9 test print confirmed that the flange fits the slot.

  • DA15: printed, not yet assembled.

  • Not tested yet: long-term use, pull force on the strain relief, printing in PLA.

The photos show real prints of version 1 (shorter hood); the other images are renders of version 2.

Files

  • <size>_hood_top.stl, <size>_hood_bottom.stl: shells in print orientation

  • <size>_hood_plate_PETG_CoreOne.3mf: both shells on one plate, with print profile

  • <size>_hood_plate_PETG_CoreOne.bgcode: sliced from the 3MF for the Prusa CORE One, PETG

  • <size>_hood_assembly.step: both shells in assembled position, for your own CAD work

  • create_hood.py, create_subd_step.py, source_README.txt: the parametric source

Source

The model is parametric and written in CadQuery (Python). The source is included as Python files, so you can change cable diameter, clearances or tie size and generate your own version. Put create_hood.py into a folder sub_d_hoods/ and create_subd_step.py into a folder sub_d_connectors/ next to it; source_README.txt lists the commands and the useful parameters.

How it was made

The model was designed with AI coding agents; I set the requirements and checked the prints.

License

Creative Commons Attribution 4.0 (CC BY 4.0): anyone may use, change and also sell it, as long as the author is credited.


Kurz auf Deutsch

Neu in Fassung 2: zwei weitere Größen (DB37, DD50), Hauben 5 bis 6 mm länger und Kabelkanal deutlich weiter (6,3 bis 13,7 mm), damit auch voll belegte Stecker Platz für alle Litzen haben. Fassung 2 ist noch nicht gedruckt; die Fotos zeigen Fassung 1. Fassung 1 (kürzer, drei Größen) bleibt als eigenes Modell unverändert online; dieses Modell ist ihr Remix.

Zweiteilige Haube zum Drucken für Sub-D-Stecker und -Buchsen mit Lötkelchen, in fünf Größen: DE9 (oft DB9 genannt), DA15, DB25, DB37 und DD50. Die Schalen halten ohne Schrauben: Je ein Kabelbinder läuft um die beiden Ohren, ein dritter um den Hals am Kabelausgang. Ein vierter Binder innen dient als Zugentlastung.

  • Du brauchst je Haube 4 Kabelbinder 2,5 mm (100 bis 200 mm lang), optional Schrumpfschlauch für die Lötkelche.

  • Druck: PETG, 0,15 mm Schicht, ohne Stützen, Außenfläche aufs Bett, Trennfläche oben wie in den STL.

  • Montage: Stecker mit dem Flansch in den Schlitz der unteren Schale legen, Zugentlastungs-Binder innen schließen, obere Schale aufsetzen, die zwei Ohr-Binder und den Hals-Binder einfädeln, festziehen, bündig abschneiden.

  • Öffnen: die drei äußeren Binder am Kopf durchtrennen, zum Schließen neue nehmen.

  • Fassung 1: gedruckt sind alle drei Größen. Die DB25 ist mit Buchse, Litzen und Kabelbindern montiert, die DE9-Schalen sind zusammengesetzt, die DA15 ist noch nicht montiert. Langzeitgebrauch und Zugkraft sind noch nicht erprobt.

  • Der Quelltext liegt als parametrisches CadQuery-Modell bei (zwei Python-Dateien und eine Anleitung). Lizenz CC BY 4.0: Jeder darf es nutzen, ändern und auch verkaufen, wenn er den Urheber nennt.

Tags