Christmas festive candle bridge
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
A festive 3D printed candle bridge suitable for 3 or 5 mm LEDs
- Rating
- 0 / 5
- Likes
- 5
- Downloads
- 39
- Makes
- 0
- Views
- 445
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Winter & Christmas & New Year's
- License
- Creative Commons — Attribution
After searching the web for a 3D printed candle bridge suitable for 3 or 5 mm LEDs and only finding several candle arches (mostly designed for tealight candles, which I would be concerned could melt), I decided to make my own and upload it to share with the 3D printing community as my first published 3D model.
Note: If you just need assembly instructions, these are at the bottom
3D printed parts you will need:
1 x Main part with boltholes (requires supports under boltholes);
1 x Main part with nutholes (requires supports under nutholes);
2 x Base plates (requires supports under boltholes);
14 x Candle for 3 or 5 mm LED (each part is half a candle, supports required under base);
7 x Candle retainer + flame
2 x M3 Bolt blanking plates (optional, these have not been tested, scale in your slicer to the appropriate size if they do not fit);
2 x M3 Nut blanking plates (optional, these have not been tested either, scale in your slicer to the appropriate size if they do not fit).
Hardware required:
A small amount of hardware will be required, these are:
6 x M3 nuts (for mounting to the base plates and clamping the 2 main halves together);
4 x M3 x 8 mm bolts (for mounting base plates);
2 x M3 x 12 mm bolts (for clamping the two halves, these will only reach to approximately half way through the nut when clamped so 14 mm may be preferable if available but 12 mm bolts have been tested and work ok).
Electronic components needed:
Additional electronics can be used in addition to the below (for example, a micro controller to flicker the LEDs if you do not have LEDs with a flickering function internally built in or a low voltage cutoff switch if using batteries to protect from over discharge) but these are outside of the scope of these instructions.
7 x 3 or 5 mm LEDs (flickering 5mm LEDs are used here);
7 x resistors of a suitable value (the resistance will depend on the supply voltage, the LED forward voltage and the current passing through the LED, see below in the assembly instructions);
1 x Battery holder, preferably switched (or any other alternative power supply such as a USB cable and power bank);
30 AWG (or larger) wire in any colours of your choice, but black and red is usual (2 metres of each will be more than enough);
Soldering equipment (Iron, solder etc);
Heatshrink to protect against short circuits (electrical tape could be used but isn't the best option).
Printing instructions:
Choice of material:
For the candle bridge I used silver/grey PETG for the 2 main parts and base plates. The candles and retainers/flames were tested with a translucent blue PLA as this was to hand at the time of designing. The finished candles were painted in a translucent yellow PLA.
I feel that PLA would probably be the best choice for the entire project as it is easier to print with. If reprinting the model again I would likely use a wood PLA filament for the base plates and main parts, white PLA for the candles and a transparent PLA for the flames/retainers to allow light to pass.
The blanking plates, if used, should be printed out of the same colour material as the main parts.
Brim and Supports:
Support will be needed under the bolt/nut holes on the base plates and the 2 main pieces of the candle bridge.
Supports will also be needed between the build surface and the underside of the candle pieces but if the support overhang angle is left at the default 45 degree then the slicer will also attempt to place supports on the section above that clamps into the candle bridge, changing the overhang angle to 50 degrees solves this problem.
A brim is recommended on the candle and the flame/retainer pieces
Layer height:
All the parts were printed using a 0.6mm nozzle (although not tested, I would expect a 0.4 mm nozzle to also work) with a 0.2 mm layer height on an Ender 3 Pro. A layer height of more than 0.2 mm will reduce the quality of the candle parts as well as preventing the two main parts of the bridge from clamping correctly on the candles. This is because they are each 10 mm thick so need to be printed using a layer height that divides into the 10 mm, in hindsight a thickness of 9.8 or 11.2 mm would have allowed a 0.2 or 0.28 mm layer height to be used, but I could not get Freecad to change the thickness after the fact without breaking existing dependencies.
The exception to the layer height rule is the base plates as these are 7 mm thick so can be printed at 0.28 mm layer height, although only 0.2 mm was used when I printed them.
Ironing was used on the base plates and the main parts for a smoother finish.
Assembly:
The electronics:
Since only a low voltage is to be used (well under 10v), the 7 LEDs will be required to be wired in parallel with a resistor connected to each LED in series to limit the current.
Depending on your power source and the LEDs you use, the value of the resistors required will be affected.
The required resistance can be calculated by the equation:
Resistance (ohms) = (supply voltage - LED forward voltage)/LED current (Amps)
For example, if using a yellow LED with a forward voltage (Vf) of 2.4v and a max current of 20mA (or 0.02A) whilst using a 3 x AA (4.5v) power supply, the equation would be:
(4.5-2.4) / 0.02 = 105 Ohms resistance
As most resistors that a hobbyist would use will be in the E12 resistor series, a resistance of 100 or 120 ohms should be chosen as 105 ohms is not in this series. Whilst 100 ohm is closer to the true value, the 120 ohm resistor will reduce the stress on the LED and increase its lifetime.
3 and 5 mm LEDs typically have a max continuous current of 20-30 mA to ensure they have a long lifespan but the forward voltages are quite different. Therefore if changing colours, such as from white (with a Vf of 3.0-3.4) to red (typically Vf of 2.1 to 2.4) it is important that the resistor value also be changed as the red LED will be over driven, shortening its life.
The resistor should be chosen with a supply voltage equal to a fully charged battery, for example, 4.2v if using a single lithium-ion cell instead of the nominal voltage of 3.6v as this will prevent over-driving the LEDs if calculating the resistance required when the cell is at 3.6v and then charging the battery to 4.2v.
It should also be noted that as the voltage in the battery decreases, the brightness of the LED will also decrease, this is a downside of using a resistor to drive an LED from a power supply of varying voltages. This can be solved by either using a voltage regulator, using more advanced driving techniques or using a device such as a USB power bank, which will deliver a constant 5v until its battery is depleted.
It is also important that you use one resistor per LED and not a single resistor to limit the current in the entire circuit. This is because if using one resistor, 140mA would need to pass to operate all 7 LEDs. This will be fine initially, but if one LED were to fail, the 140mA will now be divided between 6, which will result in the remaining LEDs being over driven which will lead to cascading failures as the current the LEDs are required to pass increases with each failure.
Using separate resistors on each LED also spreads out the heat dissipation across 7 resistors instead of one as well as allowing multiple different colours with different forward voltages to be used off one power supply, if desired.
The only other consideration is the max power that the resistor can handle, this can be calculated using the following equation:
Power = Current (A) x Current (A) x Resistance (Ohms)
If using the earlier values, we get:
0.02 x 0.02 x 105 = 0.042 W
The majority of low power resistors are either 1/8 or ¼ watt so this is well within the acceptable range. However, consideration must also be given to how hot the resistor will get, as it will melt the plastic (especially PLA) if it is having to dissipate a large amount of power that is approaching the power limit of the resistor. Therefore, it is good practice to use a reduced maximum power (such as ½ or even a ¼ of the resistor's max thermal power) which will help prevent melting plastic if it comes into contact with the resistor.
The assembly:
Whilst waiting for the prints to complete is the perfect time to prepare the electronics.
First you will need to calculate the value of the resistors required, as mentioned above for my candle bridge using 3 x AA batteries and yellow (flickering) LEDs, I will be using 120 ohms.
Next, take an LED and note the polarity (usually the longer lead is the anode and the flat side of the casing the cathode).
Afterwards, cut down the resistor and LED leads to 10-15 mm each, ensuring that the leads are long enough to avoid the solder joint being placed at the top of the candle, which has restricted space, especially after heat shrink is added but not excessively long so that the LED + resistor combo doesn't fit in the candle bridge. After this, solder one of the resistor leads to one lead of the LED and cover the solder joint and resistor with heat shrink, leaving the other lead from the LED and other resistor lead exposed. Repeat for the other 6 LEDs.
After printing and cleaning up the pieces, you are set to start building!
Take either of the main parts and place a nut into each of the holes in the bottom. Take the two base plates and use two of the M3 x 8 mm bolts attach each of the bases to the first of the two main parts. Then lay the main part + base combo on a table the with all the slots facing up then place one half of a candle into each of the 7 slots, they have been designed to stay in place in this orientation without any glue.
Next, place a resistor and LED combo in each candle half, ensuring the LED sticks out the top, above the restriction. Measure out the lengths of wire needed to connect. Run one pair of wires between all 7 LEDs one after the other in a daisy chain. After measuring out, solder the wires to the appropriate connection, being careful not to melt the plastic with the iron and remembering to add heat shrink before soldering the second end of the wire.
After everything is soldered, then take another candle half and place it over one already in a slot, afterwards secure them together with the retainer/flame. Repeat for the other 6 candles, Take the second main part and using the other M3 x 8 bolts attach the second main half to the bases, ensuring no wires are hanging out and restricting closure.
Next, insert the M3 x 12 mm bolts and the associated nuts into the main parts and tighten to secure them together. Add the blanking plates if desired after.
Connect the wires to the power source and et viola! You've made the candle bridge.
If you have made it this far (nearly 2000 words at the last count) then I hope you have a go at making your own candle bridge and I look forward to seeing other people's makes of the candle bridge and uploading more models in the future, just not with an essay-length message in the description box, like this one.
