1 / 11
V1.1.1 Hornet: Creality Sprite Extruder Cooling System Mod — image 1
1 / 11

V1.1.1 Hornet: Creality Sprite Extruder Cooling System Mod

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Multi 5015 Dual / Triple - Fan Mod for the Creality Sprite Extruder.

Rating
4 / 5
Likes
110
Downloads
391
Makes
2
Views
6,238
Reviews
2

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — Share Alike

This is an original design that I have made and am currently working on. This is still in development and a work in progress.

The Design uses 3 5015 Radial Fans to cool parts and the heat break. With the possibility for a 2 5015 fan Configuration.

 

V1.1.1: 

  • Backplate Changes
    • Noticed that the CR Touch was still hitting parts of the print during filleted overhangs / bridges 
    • Raised the Mount higher by 0.75mm from V1.1
    • One of screw holes on the back was a little too tight on tolerance. Increased the hole size to 2.75mm for easier fitment.
  • New ADXL-345 Mount
    • Added a file that goes onto the Front of the extruder for an ADXL-345
    • You will need to switch out the M3x6mm Screws on the Top Front of the Left and Right wings to M3x8mm Screws for this part.

V1.1 : 

  • Back Plate Changes
    • Adjusted CR-Touch Mount higher by 0.3mm
      • Some people have been having issues with the CR-Touch Colliding with prints.
      • This is compatible with V1.0 Existing parts, and won't require any additional reprints of the parts

V1.0 :

  • Triple 5015 Configuration uses 2 fans wired in parallel for Part Cooling
    • Using 2 Fans Instead of 3 for is a possible option for the design.
      • For a 2 Fan Configuration, remove the right wing, with only the left wing and the backplate attached.
      • This will make it so you only have 1 5015 for cooling heater block and 1 5015 for part cooling
  • Another 5015 Fan is used to cool the heat break
  • The design is kept as compact as possible (for a triple 5015 fan configuration) keeping the fans as low as possible and as close as possible to the extruder.
    • The low profile gives plenty of clearance for those running LED lights at the top of the gantry.
  • Nozzle can be easily viewed from the front.
    • No more leaning from the side to check on Z-Offset for the first layer.

 

BOM:

PiecesPart
11 - 13M3x6mm Socket Head Hex Screws
0- 2M3x8mm Socket Head Hex Screws
1M3x4mm Socket Head Hex Screws
3 - 5M3x20mm Socket Head Hex Screws
2 - 35015 Radial Fans
2M3 Nuts
1CR-Touch
1Sprite Extruder

Recommended Material: 

  • For any prints under 270C - PETG would be able to handle the heat.
  • Anything that has 100C or higher glass transition temp. would be recommended

Recommended Settings:

  • 0.16mm - 0.2mm Layer Height
  • 30% Infill
  • 3 Walls
  • 3 Top and Bottom Layers

Support Settings:

  • Overhang Threshold Angle: 45 Degrees

The Cooling system was design for as little support as possible where support on build plate is necessary. There are a few areas that require support. The Top of the heat break exhaust redirection port and within the fan ducts depending on which version.

CR-Touch Offset: 

  • X-Axis: -49.15mm
  • Y-Axis: 0
  • Bed Mesh Maximum:  250, 290

Weight: 

  • 1 5015 Radial Fan Weighs approx. ~26g 
  • 3D printed assembly total weight (not including fans and screws): 40g - 45g

Fan Duct Design

  • The Fan Duct was designed so the airflow would be able to travel the shortest amount of distance as possible from the fan to the part.
  • The outlet of the fan duct is kept as wide as possible to prevent any flow reduction going to the fans.
    • Had to narrow the height of the duct because for clearance reasons.
2 Versions fan ducts:
  • With inner walls
    • Inner Walls within the fan duct to remove the need for support for the inner portion of the ducts
    • More of a quality of life change than anything as the added inner walls slightly reduces airflow to part cooling.
  • Without inner walls
    • For set ups that can handle <15mm Bridges
    • This is the ideal set up for the most efficient part cooling

— 

Current Issues:

  • The current design, at it's lowest point has only a ~ 1mm clearance from the print bed. While I have not had any problems yet this might pose as a problem for others as it makes the design less forgiving with variance on leveled beds and warping. 
    • Could be prone to failed prints due to base of the wings hitting the part.
    • I have plans on developing a design with a higher oriented base.

Future Plans:

  • I plan to expand the platform
  • Create a modular interface to be able to use multiple types of fans
    • Add Support for both Radial and Axial Type Fans
  • Add mounting points for multiple types of accelerometers
  • Create a more modular interface for further customization on fan duct outlets

 

More Projects Planned to come! Join my Discord for more info? 

Tags