Bambu labs P1P enclosure "TINKER"

This all started while waiting on a p1p enclosure that I was happy with..  but I couldn't wait to start making stuff.   so I started making my own.  I set out to make an enclosure that didn't restrict the build plate view at all levels.   most enclosures only allow you to see the first layer via the front door.. this was unacceptable in my personal opinion.   I wanted to be able to see it from both sides and front.. so..I did exactly that…and “Tinker” came to life..      Using the most basic cad software available, I made this enclosure.   I imported all the models from the bambu 3mf files and began my process.   

Tinker requires some screws and a few nuts AND self sourced polycarbonate panels.  I need to make the BOM for it which I will do and update.  its all M3, M4, and M5 bolts/nuts.  you will also want to buy some fuzzy velcro material OR a sticky type material that is soft.. kinda like felt with adhesive on it?   I found the fuzzy section of DIY velcro to work marvelously. 

The see through polycarbonate sides and door can be sourced anywhere you'd like.  They're 1/8 thick.    Specs are as follows: 

Polycarbonate Sides:  1/8" thick and 420mm X 280MM (you'll need 2 of these..)

Polycarbonate door: 1/8' thick and 350mm X 400mm ( You'll need 1 of these…) 

**************************************************************************************************

As for the printed parts, you'll need 1 of each of them.    they're marked accordingly on the models file name.   so keep track of how you print them.   they're named according to where they'll be placed on the machine, VIEWING IT FROM THE FRONT LCD!!     These can all be printed on and ender3 sized bed.  they've all been made to be printed laying down on the face that has no items that need supported.   there is NO support needed for any of these models. (If you print them standing up, thats your call… but you'll need support then..) 

the name of the parts is pretty self explanatory.  for example: LR upper = left rear upper.    RF upper = Right front Upper.  etc.  

Right bottom piece and Left bottom piece: are made to be placed along the bottom of the printers frame and help support the poly panels when dropped into place. 

The Latch:  The latch mechanism for holding the door closed will require a hole in the poly.  its a 19mm hole (or ¾" inch") it can be placed anywhere you wish.   you could even put a couple on it if you'd like.   to make the hole, I suggest holding the latch knife inside the frame.. and then using a sharpie to trace where you need the main hole at.   Its kinda tricky but it works great.  I did this using a magnet.  I simply held the latch blade in place with a magnet then used my razor sharp eye sight (sarcasm…) and drew a cross hair on the center of the bolt hole pattern then drilled the door.   worked fantastic for me!   the latch spacer thing is designed to be on the inside of the poly door.  this makes the latch a snugger fit that prevents it from rocking or kicking out when you operate the latch.  

The hinge:  This is the weakest link in my opinion but so far mine has been working fantastic. the hole that works as a pivot can be fitted with a pin of your likings.   you can use a drill bit, a nail, etc.  the tighter, the better.  I ended up using a drill bit because it was the tightest more precise thing I could find.  and it works perfectly fine so hey.. why not… lol You can place it on either side. this will determine which way you door swings open.  Clearance the bolt holes for m5 bolts.  (NOT the holes that go through the door though.. those are m4.. clearance those for m4… youlll need 2 nuts for that inner piece as seen in the pics.)     

The Connectors:  You'll need 3 of these.  They're simply for helping hold the corner frame pieces in place and tight.   you can obviously make them any color you'd like.  these will use m5 bolts to secure to the parts you print.   make sure they have clearance holes for m5 in them.  The panels will need to be tapped for m5 bolts so you can secure the connectors. 

Lower Right Panel Brace:   This little fellow goes on the inside floor of the printer.  This screws down and braces the poly panel once its installed.  Its main and only function is to prevent the bottom part of the panel from vibrating and rattling when the printer is in motion.   cover the face of it with some velcro fuzz to eliminate chaffing and noise.  works like a dream! haha 

Please dont hesitate to ask questions.  ill do my best to answers them.  hope its useful to someone else other than just me.    -WagZ-