1 / 12
AnkerMake M5 Dual 4020 sidemount part cooler ducts — image 1
1 / 12

AnkerMake M5 Dual 4020 sidemount part cooler ducts

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Reduce sound without compromising print quality!

Rating
4 / 5
Likes
63
Downloads
351
Makes
2
Views
2,329
Reviews
2

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — Share Alike

Update: Revision 8 - (R8/R8-Solid model in printable files):

  • Hex edge thickness increased to improve stability and printability
  • Solid version included (easier to print than hex, slightly heavier)
  • Slightly adjusted vent angles.
  • Improved clearance against printhead

Update: Revision 6 - (R6 model in printable files):

  • Hex cutaway to reduce weight (11g vs 15g)
  • Vent supports added with a baffle to the tip to prevent overcooling of the nozzle/heatblock
  • Slightly more vent area on the left side vent
  • Angled downwards a bit more 
  • Enlarged the screw mounting holes
  • Added a fan cable route-through on the left side
  • Flattened vent bottom to allow for printing without any supports on the side vents (supports still required for the faceplate section)
  • Additional clearance between duct tips and the heat block

    above - R6 model
     

Update: Revision 5 - (R5 model in printable files):

  • 1mm extra clearance between the nozzle tip and the bottom of the ducts - at slightly reduced vent volume.  
  • removed fan mounting holes that were inaccessible due to placement against the extruder parts
  • added some extra braces
  • added some extra vertical adjustment via the mounting holes
  • been printing with it for 1 week now with no issues.

    above - R5 model

Background:

While 4020's aren't as quiet as a 5015, the airflow is generally higher and you can use standard issue 4020's instead of a high-end 5015 (currently it seems only the TH3D one seems capable of supplying enough airflow). 

I printed overhang towers to make sure this design flows at least as much air as the stock cooler. I've noticed it performs a bit better than stock on fast Y movement (bed moving quickly, extruder stationary) since it provides a wider (deeper) cooling path than the stock ducts which are centered on the nozzle and create a rectangular flow. 

I tried with both my sleeve bearing 4020's ($4 electronics store specials) and higher-end dual ball bearing model - both are sufficient. 

You can print down to ~80% fan speed without a degradation in quality, from my testing (depends heavily on your fan specs). I noticed that as you reduce fan speed, you will hear the "whining" sound of the fan pushing against the duct restrictions also lessen. When it is no longer whining, you've essentially matched the fan speed and static pressure to the duct size. You can do this on the printer itself during a test print and see during printing. 

Stock fans printing 1M away is about 61-62db, this is 50-52db which, in person, is much quieter. The stock hotend cooler fan (4015) is a bit louder. 

 

To Print: 

I've printed it successfully at 200mm/s standing up with tree supports - I didn't have to fiddle with bridge settings to get it to span the ducts. I've tapered things where possible to reduce the amount of supports needed to print.

With 16% infill, it comes out to 15g of filament.

Since it doesn't get very close to the hotend, you can print it in normal PLA+ without it deforming during use.

To Mount:

Remove the stock dual-3010 bracket and fans with the two rightmost screws on the hotend.  Keep the screws as you will use them to affix this duct bracket to the extruder.

For the fan screws: M3-0.5 x 15mm should work without sticking out past the back of the mounting plate (m3-0.5 x 16mm pictured)  You should use all 6 since the extruder can get moving pretty quickly and could work the fans loose.  

Route your fan cables closer to the ducts or over the fans, as you don't want them touching the hotend.

Tags