Counting matching models…
Customized version of https://www.thingiverse.com/thing:3132978 Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=3132978 Instructions Using the following options: width = 35 height = 22 length = 200…
jde jen o redukce v napojovem drzaku drzak mam u me v modelech také
Originally designed for the Makita LS1110F mitre saw and the Parkside PWD vacuum cleaner. Compatibility with other models is possible. Highly durable, simple design. Printing from PETG - perimeters only. Navrženo pro pokosovu pilu Makita…
A fully parametric OpenSCAD reducer designed to connect a ~4" duct to a ~2.5" outlet. I built this to adapt the exhaust from a Creality Falcon A1 (~60 mm ID) to an AC Infinity inline fan (~102–103 mm ID). The model uses matched…
Choose the pipe diameter you are using. For best result, print with 4 perimeters. If you need more dust collection fittings, see me website https://woodworkers3dp.com/
Print two of these to join a flex duct through a screen! Designed for 4" ducting like this: http://smile.amazon.com/FO450-5-ply-Supurr-Flex-Aluminum-Ducting/dp/B00009W3H2/ref=sr_1_2?ie=UTF8&qid=1412923160&sr=8-2&keywords=flex+ducting…
The cage for the hot end for the effector by @RyanMaverick_259405 is about 3mm too short for me. This leaves a gap between cage and the effector plate as well as the duct fan and the effector plate. The gap between the effector plate and…
This is a scoop that can be used to align multiple smaller envelopes (3.5 inches wide) into a larger clear envelope for a neatly packaged outcome. I use it to load lures already packaged in smaller bags into packages and multi-pack…
Ein Modell von einem Kabelkanal für Alu Profile der 30er Reihe TypB mit 8mm Nut. Zum einen dient der Kabelkanal zur Verlegung von Kabeln und außerdem noch um einen 10mm LED Streifen auf der Außenseite zu befestigen und so z.B. eine…
Adapt your 100mm (4 inch) air duct to a 150mm (6 inch) duct, with option to add an inline 140mm PC fan. To install: Print one of each part Insert M3 threaded inserts into the 4 outer holes on each side of the middle piece Use four anti…
I don't use the Y that came with the dust collector since I use a cyclone separator, so I created this adapter. It has a shoulder in the fitting that rests on the inlet flange of the blower. It also does not go all the way down to the…
Part cooling duct for biqu h2 and biqu microprobe mount. Need 2x m3x3x3.5 heat set inserts for fixing the 5015 fan and 2x m3x3x3.5 heat set inserts for fixing the probe. Added v2 for less supports when printing. Apply some glue to…
Hi guys, We all must give BIG THANKS TO Justin Fritz because he was the person who asked me and helped me a lot to make this model together. I don't have the latest revision of the K1 MAX, but with the help of his tape measure and a few…
This is the 45x12 mm version of the Cable Duct for 4545 profiles. It comes in three lenghts, 50 mm, 100 mm and 150 mm. Also see my other models different sized versions.
This is the 45x23 mm version of the Cable Duct for 4545 profiles. It comes in three lenghts, 50 mm, 100 mm and 150 mm. Also see my other models different sized versions.
This is the 45x45 mm version of the Cable Duct for 4545 profiles. It comes in three lenghts, 50 mm, 100 mm and 150 mm. Also see my other models different sized versions.
This is a heat exchanger for 6in ducting. As an example, I used it to temper incoming makeup air for a basement kitchen hood's exhaust. I printed using carbon fiber reinforced PLA. I don't have the equipment or knowledge to test the…
Модификация системы обдува 3D-принтера Flashforge Adventurer 5M Modification of the Flashforge Adventurer 5M 3D printer blowing system Печатать без поддержек и отключить замедления на внешних периметрах Print without supports and disable…
Pretty basic model. I made the base thick so it would fit nicely in my window and have a little weight so the duct wouldn't keep pulling it out.
Esta plataforma giratoria motorizada es ideal para fotografía de productos u otros usos similares. El diseño consta de dos piezas simples: Base: Sostiene el motor de manera segura. Plato superior: Gira para mostrar tu producto. La…
The hammer is not functional it is theater prop, I made it lightweight with exaggerated hammer head to make it more noticeable on stage. There is no any logos on the hammer. Model has two separate parts (the head and the handle) you can…
V1.0 I may need to update this model. But you are welcome to try it out yourself. Most likely, it would just need a slight scale adjustment. V1.1 Added taller slots for cables. V1.2 Moved switch slot 3mm
печать из материала ABS или PETG @сопло 0,4 мм you will need 2 bolts and 2 nuts, which are best soldered
Originally designed for the Makita LS1110F mitre saw and the Parkside PWD vacuum cleaner. Compatibility with other models is possible. Highly durable, simple design. Printing from PETG - perimeters only. Navrženo pro pokosovu pilu Makita…
also used this as a base for the mounting bracket: https://www.thingiverse.com/thing:2850837
using this fan bracket: https://www.thingiverse.com/thing:2850837
Custom use case fan duct for this great fan to ssd mount, by MLoeko . There is both spacer pillar and the wall file. This lets you mount a full set of drives clamped between two sets of the SSD mounts using threaded rod in the fan…
Someone needed an air intake that blocks the light from passing through so I designed one. The hole you need to make is 68mm in diameter. I'm far to stupid to make this parametric, so this size wille have to do. You can always install 2…
This 4010 extended blower duct is specifically designed to optimize airflow for the K1 CHC (Ceramic Heater Core) Hot End , seamlessly integrated with the Toybox Alpha 3D Printer's stock fan location . The duct channels airflow efficiently…
This a new 5015 intake for the delta P duct v2r22 addon with a cone airflow entry. Did not like like the existing ones very much so I made this. On a bench test the inside cone improves cooling airflow by 3-8% (depending on cooler speed).…
Уменьшение стука стола при Z-HOPE: фиксатор гаек ходовых винтов. Нужно два фиксатора на передние стойки (-SIDE) и один на заднюю (-BACK). You need two retainers for the front struts (-SIDE) and one for the rear strut.
It is now possible to mount a Bambu A1 hotend, making it easy to change nozzles. The settings on the Prusa MINI+ side can be used as is without any modifications. There is also an STP file, so someone please create a cutter mod and Remix…
I needed a junction box to hold a small 5V PSU-Board as well as a Relais-PCB within an REV-Ritter cable duct. Here is an qick model for that. It can be fixated wihin the duct with the two T-Screws. I left some space on the bottom of the…
For all of you who might feel that your stock TEVO tarantula's hot end is inadequate in that it doesn't have a part cooling fan nor a mount for an inductive sensor, than these parts are for you. The fan vent holds a 5015 fan and provides…
I needed a low profile fan duct for my HBA card inside my space constraint hp EliteDesk 800 G4 SFF so I created this. It uses an 4010 radial fan (mostly found as part cooling fans for 3d printers). As I only had a 24V fan laying around, I…
The hot air exit inside the van got very hot, i printed it out of PC at first which should be good up to 100-110 degrees C but that was not enough. The last iteration i printed in carbon fiber reinforced nylon (PA-CF) which hold up great.…
The recommended z leadscrews for the Ender 3 NG left my Mk8 hotend nozzle too far away from the buildplate - the z offset between my probe and nozzle was almost 10mm. The hotend mount has been modified to lower the nozzle ~8mm towards the…
Scalable NACA Air Inlet – Seamless Aerodynamic Integration Enhance airflow efficiency with the NACA Air Inlet , designed for seamless integration into a variety of applications, from automotive hoods and body panels to RC aircraft, UAVs,…
I think this duct design is at it's core one of the better options you can find for this printer. It does have overhangs though that would be prone to sagging. I made a version with basically identical dimensions, but with chamfers that…
This is a quick and easy 3D print that transforms a finished duct tape roll into a useful container. Just print the lid and base, attach them to the roll, and you're done! Great for storing small items like screws, clips, or coffee…
This adapts a 80mm fan into the 40mm hole which has the nozzle exhaust chamber. I haven't got it working as the fan it's replacing is 24v and I don't know how to get 12v power to the fan. Check my other model which is the nozzle exhaust:…
A replacement nozzle cooling system with a duct to fit an 80mm fan. Haven't tried it yet as I'm looking for a way to convert 24v to 12v for the fan. Check out my other model for the fan Duct:…
This is the WD My Cloud EX2 Ultra fan cover replacement modified for 92mm fan. 70mm version and additional details are avaible here: https://www.thingiverse.com/thing:5177184…
The 90-degree elbow reducer is used for hot air heating from 3.5" to 2.5". PA-cf recommended for temperature resistance
This custom holder is designed to store up to 8 PASCO conductivity sensors safely and efficiently. Each sensor fits into a dedicated slot with a recessed base to prevent slipping. The structure saves space and keeps the lab organized. The…
With High Flow Nozzles (CHT) and when printing with PLA and due to the improved heating of the micro swiss hotend you have to adjust the print settings / print temperature and take care of retraction settings etc. because it is really…
Customizable in OpenSCAD. My is for TT scale. Print Settings Printer Brand: Anet Printer: A6 **Rafts:** No Supports: Yes **Resolution:** adaptive 0.07 to 0.2 Infill: 25 **Filament:** na3d PLA silver Notes: Printed upside down, in 3 pcs.…
In the second version I removed the ugly step :)
The duct sits directly on the heat sink of the CPU of a Futro S920. For power I used the fan connector on the board. (And a left-over silent-adapter from a Noctua fan, to silent it a little.
I have an inline bathroom exhaust fan, but needed to connect it to three vents without running back to the store. Glue and fit the panels. A blanking plate model is included if you don't need all four.
Ive modificate the clip for BootyCall Jones linear carriage und useable for heat inserts M3x4x5mm. The duct also got a heat insert. Print settings up to you. Ive used 10% infill with ABS.
Eta battery vacuum cleaner reductin nozzle to 32mm outer diameter 2 versions (both is simmilar, but v2 has only different geometry) outer diameter is 31,8mm for better compatibility Print settings 0,2mm layer 4 walls no supports use outer…
Bridges the gap between the fans in the Fractal Ridge and the GPU heatsink. Helps with focusing airflow directly over the fins of the heatsink, improving cooling. Requires deshrouding the graphics card. Compatible with Fractal Ridge case,…
Was looking for a good fan duct with 360° cooling and good nozzle visibility of Kobra S1 and decided to make this one for upgraded hotends (with ceramic heater). The model is easy to print with or without supports (up to you). Please…
UPDATED: 2026-01-05 the V3 models below are the good ones... I have greatly improved the airflow and printability of the model. It is now possible to print with the front face at a 45 degreee angle to the build plate, which greatly…
15% infill PLA or PETG No need for support Suits for 2mm² cable M4 screw holes
15% infill PLA or PETG No need for support Suits for 6mm² cable M4 screw holes
I couldn't find the Throttle Lever for a lost CH Products Flight Yoke, just the Mixture and Prop Levers were available. I printed it in Polymaker ASA normal settings without supports.
My triple slot GPU was running a bit hot on the NR400 despite having 3 intake fans installed, so I made this to improve the airflow to my GPU by mounting it right behind the fans on the front of the case, on top of the hard drive cage on…
This set of files includes 3D-printable recreations of most Creature-And-Character-Building-System hands, feet, and armor accessory elements produced by Lego from 2011-2016 for the Hero Factory and g2 Bionicle lines. All elements are…
Hier findet Ihr ein Modell eines 3-teiligen Luftkanals um den Schlauch einer mobilen Klimaanlage mit Außendurchmesser 150mm besser als mit der originalen Halterung an einem Dachfenster befestigen zu können. Der Kanal ist insgesamt 38cm…
Adapter to connect a 41mm diameter (OD) hose to the SV08 enclosure exhaust port. This is the diameter of the Mars Mate air purifier hose, so that the printer can be connected directly into the Mars Mate. If the hose connection is slightly…
[ENG] Replacement air channel for RPK CYMA airsoft replica. Recommended to print on the front of the pad with a layer height of max 0.2mm with a larger number of perimeters. For stability when printing it is better to print with brim. It…
Try the newer version! I highly recommend using V2 of this model instead. I'm keeping V1 as a separate listing because of the weird duct angles that aren't supported in V2. I never used those weird angles, however, so not sure how well…
Left Headlight Duct 3d .STL model for Honda CIvic EJ/EK (facelift version: '98-'00). Deigned specifically for K-Swapped cars with air filter on left side. Mounting holes to be drilled upon fitment. Package includes: -Entire headlight as a…
Important! Measure the pin on the heatbed is 4mm or less; if the pin is too high, the duct will clash with it and may cause damage! (You may try to grinding the pin down a bit or cut this model from the duct side by 1mm or so to make it a…
Background I bought the Ender3 V3 KE this year (2025) and it seems the original FatBurner toolhead cover is not fully compatible with my revision of this printer, so I ended up printing Ronald Rademaker's combined version. It fit and…
12mm to 18mm inductive probe adapter, screw fit Category: 3D Printer Parts
Customized version of https://www.thingiverse.com/thing:1109880 Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=1109880 Instructions Using the following options: tipLength = 28 tipWidth = 3 tipDistance =…
Prusa Core One + Particle Evacuation System Print Settings: This model is optimized for PETG printing at a 0.2mm layer height. Supports are required for: The base The upper part of the closure valve The pipe elbow update : Base horizontal…
This model was created specially for using with Volcano nozzles, but it works just fine with original (proprietary) sovol nozzles. NOTE! You need to extend the cable for about 30-40mm so it reaches the connector It is recommended to print…
This is a remix/repair of the 90-degree vent hose model from RobertCowen for the Xtool P2 and P2s. The models that he has posted for this specific part have artifacts present in them that stop both the 3mf and STEP files from printing…
This is a mod to change the original part cooling fans from the Raise3D Pro2 to using blower style 4010 which provide much, much more cooling power. I used the DragonBurner V8 design and made a few cuts and adjustments to it would fit the…
The Step rebuild of the CR-5 PRO Fan Duct with step files. The rebuild dosen't match the original 100%, but at the import parts. The red Part shows the Original and the green the rebuild by my self.
Builds clean enough on an Elegoo Centauri Carbon without any supports or brim in PLA. Made to be press-fit onto the Elegoo Centauri adapter by Synthetic Electron 3D . You may need to glue it for a secure attachment or adjust the size for…
These Files are Version 2.0 of the HAF Case Top Cover Fan Duct. This is a Fan Duct designed to cover the top opening of the HAF 912 Case. This model has locator pins that use the watercooling holes. If you want a version that uses other…
If you like what I do here, come visit my (German) Discord or my Facebook group. Discord: MX-creations Facebook: 3D printed Grow Tools & Accesories - free .stl - v1.0 is used for coupling 100/125/150mm - v1.3 is used for coupling…
This is a remix of @GalvanicGlaze’s Diplo Duct – Ender 3 V2 4020 BMG Direct Drive. I’ve modified the model to better suit my setup: Adjusted the backplate to fit my linear bearing mount for the hotend Modified the extruder mount to work…
Please use M3 SHCS screw to attach your Orbiter Extruder as the thick screw head will make the cutting arm stop at the right place.
I despise M2 screws. They're impossible to install. They use a 1.3mm hex that strips if you look at it wrong. This remix gets rid of the M2 screws and uses 2x of the existing screws from the OEM assembly. The intake and fan mount slide…
UPDATES 11/16/25 Added versions of both cooling ducts for the smaller 4.1-4.5mm wide heat inserts. This is a lightweight fan duct based off of my original cooling duct design for the Qidi Q2. The duct with both heat inserts and bolts…
Cradle to hold and charge your Phone - in this case done and shown for a iPhone 12 with a very lean case. BoM: Brodit vehicle mount |…
Default model (stock probe) -- the probe position remains the same as in stock ; no offset correction is required. BOM : Default model (stock probe): heatbreak fan: 1xM2 16mm bolt + printed heatbreak fan-16mm-bolt-mount model fans: 2xM3…
This is a front exhaust / intake shroud designed specifically for the Cooler Master QUBE 500 . My first print (with supports and before I realized a cutout was needed) used approximately 200 g of ABS . The final print shown may look rough…
The WIFI camera (model v12) doesn't hold well on the original rubber ring. I created a reduction ring that holds everything firmly in place after removing the rubber ring. I use it with the SVBONY MC25-75x70 scope.
Description The stock model cooling fan duct sucks. Here I have redesigned one. The main purpose is to add air flow guiders so the cooling air could be more even and stronger. To maintain the dimension is important so it would not cause…
A zero support wye/tee fitting for 4" duct systems. designed to print without supports! You'll need a brim, though, because there's very little contact area on the build plate. it's 4" OD, so the duct slips over it. I printed in both ASA…
This model is an extension of the original cup base of the Delta Q Mini coffee machine. The original cup base positions the cup relatively far from the coffee spout, which can cause splashing during extration, leading to mess. The…
Bracket designed to allow for mounting of 5015 fan and 8mm inductive probe to NF-Wind (or clone of thereof) extruder. Mounting height is optimised for use with TriangleLab CHC Pro. 5015 fan to be mounted via 3mm screws with heat-set…
Check out the original creator’s model for more info and the source design.
This is a remix of FabulousD_564891's model. Motivation : My V3 KE doesn't have side screw holes on the extruder motor (see image), so FabulousD_564891's model doesn't work for my machine. I have to redesign the upper part of his model.…
Artillery extruder cover fan duct for x4 for better airflow and custom design.
Use the FCStd files if you wish to change the models in FreeCAD, and use FreeCAD 1.1 or later. Use the STEP files if you wish to change the models in some other CAD. Use the STEP or STL files to print as-is. The STEP files may need to be…
IMPORTANT!! If you plan on using the mountains + aqueduct together, please remember to scale one or the other to whatever tolerance you see fit. I HAVE NOT DONE THIS!! In addition, the file attached contains both the aqueduct and terrain.…
![[Remix] Kingroon KP3s Pro V2 - Fan duct (redesign (STEP) and reduced (2x STL))](https://media.printables.com/media/prints/20b7aafb-fcc9-420b-af49-b4f14f45c301/images/10859124_8d45adaa-c782-4689-8a4b-a2aa0410be4b_e61b82b1-7094-44b6-8ae3-0af886071564/2025-10-09-23_49_25.jpg)
