1 / 12
Spool Holder for Da Vinci Jr. 1.0 (Open Smart Tag Upgrade) XYZprinting — image 1
1 / 12

Spool Holder for Da Vinci Jr. 1.0 (Open Smart Tag Upgrade) XYZprinting

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Use larger spools in your Da Vinci Jr 1.0 while keeping the main door and one side panel !

Rating
5 / 5
Likes
5
Downloads
66
Makes
1
Views
1,507
Reviews
1

Updated at source:

Model information

License
Creative Commons — Attribution — Share Alike

Intro:

So I bought the official Open Smart Tag from XYZprinting and a Prusament Galaxy Grey spool. I thought the way I would make this work would be by rewinding my XYZprinting spool with the new filament. But then I realized that maybe it could fit with a modified spool holder and by removing the left black support of the door. So I opened everything took some measurement, did some Blender magic and tada ! This is actually the second version because I forgot the positions of a few screws but this final version is essentially perfect (you shouldn’t need to drill or sand anything).


Disclaimer:

Obviously this isn’t officially supported so do this at your own risk ! Some of these connectors are fragile and must be handled with care (I am not responsible if you break something) !

Also for this to work you will need to remove the NFC tag (which is essentially a sticker) from the filament holder and as you can see from the pictures this is a tight fit (it’s not perfect but it works). And the left side panel won’t fit anymore.

If you are being careful with everything you should still be able to revert to the original state of the printer (but once this is installed old XYZprinting spools will NOT fit anymore).

 

Parts list:

With that out of the way, here is what you’ll need :

  • 4x 608zz-bearings (can be found on Amazon)
  • XYZprinting’s Open Smart Tag for the da Vinci Jr. 1.0
  • A new filament spool (Prusament 1 Kg PLA is what I used) 
  • Preferably electric tape (or classic tape)
  • Screwdriver 

 

How to build :
 
Before starting you will need to print the daVinciJr_Spool_Holder once, the NFC tag holder once and the Pin four times. Install the four 608zz bearings with a hammer if necessary and make sure they spin well.

You can actually start by following XYZprinting’s instructions from a YouTube video up to 1:30 (the last step here is to remove the black door support on the left side) :

(activate the subtitles of the video for instruction)

after that you will see that the spool holder is held by two slightly larger screws, remove those and keep them for later use. The black spool holder is attached to a cable so be careful. There is one screw on the side that was facing inside the printer, remove it and you will see the NFC chip reader loos, unplug carefully the cable.

 

Back on the other side unscrew the two screws that hold the pcb previously connected to the NFC chip reader. This pcb also has a cable attached, unplug carefully.

You can then slide away the black plastic spool holder and keep it if you wanted to revert to the previous configuration in the future (don’t forget the screws).


Now you can remove the NFC tag of the Open Smart Tag (the white circle inside), with your nail slowly lift it a little bit all around, it will come off by itself.

Install it in the middle of the 3d printed plate (NFC tag holder) and like in picture 6 you can fix it using electric tape. Now plug the two boards back together and turn on the printer to make sure the Open Smart Tag is being detected as filament (picture 7).

As shown in picture 8, this is how the electronics will be arranged it’s relatively tight to make sure it won’t move in the future.

Using electric tape and carefully lowering down the new spool holder, everything should fit into place. Surprisingly the hardest thing was actually the last one, aligning the two nuts in the frame to screw the spool holder is a little challenging but feasible if you take your time (for this you can reuse the two screws we removed from the original spool holder).

Place your new Prusament spool on the spool holder, screw back the top cover and the right window hinge and it’s finished ! Load the new filament and voilà !

It’s a tight fit but again it works ! It can’t be moved to the left because of the metal tab, can’t be moved to the right because of the metal frame and the door and moving it up or down won’t really change the problem. But it works ! 

 

Conclusion : 

I think it’s worth it to take full advantage of the Open Smart Tag and this allows you to have a lot more filament available for larger prints while retaining the iconic XYZprinting design. You can also remove the door completely if you think it slows down the spool too much or if you have issues with the stepper motor not able to feed the extruder well enough.

If you have an idea to make it better please leave a comment ! Thank you ;)

Tags