light up the BambuLab P1P (USB 5V COB LED, Relais, JST GH 1.25, Bambu Lab)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
COB LED illumination for the BambuLab P1P, switchable like the original LED lighting via app, slicer and printer itself
- Rating
- 4.333 / 5
- Likes
- 80
- Downloads
- 219
- Makes
- 4
- Views
- 6,420
- Reviews
- 3
Updated at source:
Model information
- Source
- Printables
- Category
- Bambu Lab Parts & Upgrades
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Once again, a clear note: Do not install these additional LED strips directly on the connection where the original LED strip is connected!
The current requirement is too high and you will at least damage the front panel board!
v2 (update 10.02.2024)
→ Update for the LED strip on the left-hand side if a camera is installed.
- Print files: (I printed the parts in ASA without any special settings)
- 1x BambuLAB_P1P_Relay_box_v01
- 1x BambuLAB_P1P_Relay_box_lid_v01
right or left LED strip without camera: - 1x BambuLAB_P1P_LED bracket
- 1x BambuLAB_P1P_LED_shutter
left LED strip with camera - v2_BambuLAB_P1P_LED_bracket_left
- v2_BambuLAB_P1P_LED_shutter_left
v1 (orig. version)
Complete set to bring light into the build space of the P1P. Compatible with the popular housing ARC for Bambu Lab P1P.
All parts are screwed, no contacts are exposed and can cause a short circuit.
Light is switchable like the original LED light. The specifications of the LED_connector on the board are not violated, because the USB connector provides the power for the LEDs.
One LED strip can be connected on the right and/or left side. The print files fit both sides and have the appropriate holes and openings for right and left mounting.
Because there is no exact 3D model where the relais box is located, it took a lot of trial and error until the box now fits :)
The assembly is simple:
- Insert the double stranded wire into the LED bracket
- Solder the stranded wire to the LED strip
- Fix the LED strip in the bracket with the double-sided adhesive tape
- Glue the shutter to the bracket with super glue
- lay cable
- lead the cable into the relay box and connect it (see connection diagram)
What is required:
- Print files: (I printed the parts in ASA without any special settings)
- 1x BambuLAB_P1P_Relay_box_v01
- 1x BambuLAB_P1P_Relay_box_lid_v01
Per LED strip: - 1x BambuLAB_P1P_LED bracket
- 1x BambuLAB_P1P_LED_shutter
- other hardware:
- 1x 5V LED strip (8cm high, per side approx. 28cm) e.g. https://www.amazon.de/gp/product/B08S35D6HK
- 1x 5V single channel relay e.g.
https://www.amazon.de/gp/product/B07BVXT1ZK - 7x M3 thread insert (5 x for relay box and 2x per side for LED mount) e.g.
https://www.amazon.de/gp/product/B09NYLSKPY - 7x M3*15 screws
- 1x JST GH 1.25mm connector (amazon often sends the wrong connectors) I used the following suitable ones
https://www.ebay.de/itm/184844268251 - 1x USB-A 5V cable e.g.
https://www.amazon.de/gp/product/B07TYNDP4K - approx. 1m double stranded wire e.g.
https://www.amazon.de/gp/product/B0764H2116
- tools needed:
- Soldering iron
- Superglue
- screwdriver
that's it :)