Anpassbarer LACK Enclosure Spulenhalter für große und kleine Spulen / Spool holder for large and small spools
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Ergänzungen zum LACK Enclosure MMU Kit bzw. Standalone LACK /Additions to the LACK Enclosure MMU Kit or Standalone
- Rating
- 0 / 5
- Likes
- 5
- Downloads
- 35
- Makes
- 0
- Views
- 805
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Printer Parts & Upgrades
- License
- Creative Commons — Attribution — Noncommercial
English see below
Wer sich das Prusa LACK Enclosure V2 gebaut hat und eine MMU2 besitzt, hat vermutlich die Spulenhalter für 5 Filament Spulen gedruckt auf den LACK Deckel gebaut. Nachteil dieses Spulenhalters: Die großen Filamentspulen passen nicht. Abhilfe schaffen verschiebbare Spulenhalter
Ich habe dazu das mittlere Teil 3 durch eine neue, anpassbare Version ersetzt.
Verwendet man eine große Filamentspule, braucht man eine breitere Rolle. Dazu werden gleichzeitig zwei Spulen für Standardfilament so weit wie möglich verkürzt. Man kann in dieser Konfiguration maximal 4 Standardspulen plus 1 große Spule gleichzeitig verwenden.
Vorbereitungen für Besitzer des MMU2 Kits: (wer keine MMU besitzt kann weiter unten weiterlesen)
Ausdruck Spulenhalterung:
Ich habe für alle Teile Prusasalicer 2.6 Alpha 6 verwendet (mittlerweile ist die Beta Version verfügbar, diese sollte kompatibel sein). Bitte alle EMF Dateien als Projekt öffnen.
- Ausdruck des Ersatzspulenhalters Teil 3 (Bodenplatte.3mf)
- Ausdruck der beiden Ständer (Schieber rechts links Prusa.3mf).
Für die Ständer habe ich Infill Modifier verwendet, um die „Klammer“ stabiler zu machen. Ich denke, dass dies nicht wirklich nötig ist, ich wollte einfach mal mit den Modifieren experimentieren.
Nun wird der mittlere, auf dem LACK Gehäuse montierte Spulenhalter entnommen und durch die neue Bodenplatte ersetzt. Bevor diese jedoch eingeklebt (doppelseitiges dünnes Klebeband) wird, werden die beiden (linke, rechte) Ständer, wie auf dem Bild gezeigt, aufgeschoben. Bitte die beiden Teile nicht verwechseln, sonst passen sie nicht zu den beiden äußeren Ständern und die Spulen lassen sich nicht einsetzen.
Ausdruck der 3 Sonderformatrollen:
Hier gibt es zwei Optionen:
- Sonderrollen schmal und breit.3mf oder
- Sonderrollen schmal und breit ohne Kugellager.3mf
In der ersten Option kommen die Kugellager aus dem MMU2 Kit zum Einsatz. Wer diese nicht verwenden möchte, kann die zweite Option ohne Kugellager verwenden.
Achtung die Spulenhalter mit Kugellager am besten als Projekt im Prusaslicer 2.6 öffnen. Ich verwende hier die organischen Aufmalstützen für das „untere Lager“
Anpassungen der Spulenachsen aus dem MMU2 Kit:
Zwei Achsen aus dem MMU2 Kit werden auf 97,5 mm gekürzt. Die beiden abgesägten Teile werden mit einer weiteren Achse aus dem MMU2 Kit verwendet, um zusammen mit dem Achsverbinder (AchsVerbinder.3mf) wie abgebildet zu einer langen Achse verbunden. Dabei muss ein Alu - Reststück nochmals entsprechend gekürzt werden, sodass die neue Achse 156 mm lang ist. Man kann den Achsverbinder mit oder ohne Sekundenkleber in die Achsen einschlagen.
Anwendung
Nun können die Filamentrollen entsprechend ihrer Größe auf die alten bzw. neue Spulen eingesetzt werden.
Vorbereitungen für Besitzer ohne MMU:
Der Spulenhalter eignet sich auch für Besitzer des LACK Enclosures ohne MMU. In diesem Fall sind noch keine Spulenhalter vorhanden.
Dann druckt ihre einfach die einfache Bodenplatte (Bodenplatte Standalone.3mf) und die beiden Ständer (Schieber rechts links Prusa.3mf )aus. Ihr benötigt dann nur die große Spule. Ladet dazu Sonderrollen schmal und breit ohne Kugellager.3mf als Projekt in den Prusaslicer und löscht die beiden kleinen Spulen.
Nun müsst ihr euch noch die Achsen besorgen (z.B bei Amazon): Benötigt werden folgende Längen: 2 mal 97,5 mm und 1 mal 156 mm
Nun klebt er die Bodenplatte vorne mittig auf das Lackgehäuse.
Zuletzt druckt ihr die Filamenttülle (Tulle.3mf), bohrt mittig ein Loch in den LACK Deckel (9 mm) und steckt die Tülle ein.
English
If you have built the Prusa LACK Enclosure V2 and own an MMU2, you probably have the spool holder for 5 filament spools printed on the LACK lid. The disadvantage of this spool holder is that the large filament spools do not fit. The remedy is a sliding spool holder
I have replaced the middle part 3 with a new, adjustable version.
If you use a large filament spool, you need a wider spool. For this purpose, two spools for standard filament are shortened as much as possible at the same time. You can use a maximum of 4 standard spools plus 1 large spool at the same time in this configuration.
Preparations for owners of the MMU2 kit: (those who do not own an MMU can read on below)
Printout coil holder:
I used Prusasalicer 2.6 Alpha 6 for all parts (meanwhile the beta version is available, this should be compatible). Please open all EMF files as a project.
- Printout of the replacement coil holder part 3 (Bodenplatte.3mf)
- Printout of the two stands (Schieber rechts links Prusa.3mf).
For the uprights I used infill modifier to make the "bracket" more stable. I think this is not really necessary, I just wanted to experiment with the modifiers.
Now the middle coil holder mounted on the LACK case is removed and replaced by the new base plate. But before gluing it in (double-sided thin tape), the two (left, right) stands are slid on as shown in the picture. Please do not mix up the two parts, otherwise they will not fit the two outer stands and the reels cannot be inserted.
Printing the 3 special format reels:
There are two options here:
- Sonderrollen schmal und breit.3mf oder
- Sonderrollen schmal und breit ohne Kugellager.3mf
In the first option, the ball bearings from the MMU2 kit are used. If you do not want to use these, you can use the second option without ball bearings.
Attention the spool holders with ball bearings are best opened as a project in Prusaslicer 2.6. Here I use the organic upright supports for the "lower bearing".
Adjustments of the coil axles from the MMU2 kit:
Two axles from the MMU2 kit are shortened to 97.5 mm. The two cut-off pieces are used with another axle from the MMU2 kit and connected together with the axle connector (AchsVerbinder.3mf) to form a long axle as shown. A leftover piece of aluminium must be shortened again so that the new axle is 156 mm long. The axle connector can be hammered into the axles with or without superglue.
Application
Now the filament rolls can be inserted according to their size on the old or new spools.
Preparations for owners without MMU:
The spool holder is also suitable for owners of the LACK Enclosure without MMU. In this case, no spool holders are available yet.
Then simply print out the simple base plate (Bodenplatte Standalone.3mf) and the two stands (Schieber rechts links Prusa.3mf ). You will then only need the large reel. To do this, load Sonderrollen schmal und breit ohne Kugellager.3mf as a project into the Prusaslicer and delete the two small coils.
Now you have to get the axles (e.g. at Amazon): You need the following lengths: 2 times 97.5 mm and 1 times 156 mm.
Now glue the base plate in the middle of the front of the lacquer housing.
Finally, print the filament grommet (Tulle.3mf), drill a hole in the centre of the LACK cover (9 mm) and insert the grommet.