1 / 15
LowRider 3 CNC - Add-on - KINEMATIC Pen Holder - designed for LR3 Dust Shoe (v4.1) — image 1
1 / 15

LowRider 3 CNC - Add-on - KINEMATIC Pen Holder - designed for LR3 Dust Shoe (v4.1)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

LowRider 3 CNC - Add-on - KINEMATIC Pen Holder - designed for LR3 Dust Shoe (v4.1)

Rating
0 / 5
Likes
25
Downloads
220
Makes
2
Views
1,290
Reviews
0

Updated at source:

Model information

Category
Tools
License
Creative Commons — Attribution — Noncommercial

This is made to go with the LowRider v3 CNC - KINEMATIC Tool-less Quick-Change Accessory Holder - supports laser, drag knife, pen, etc (v4.1). 

NOTE: July 28, 2023 — Consider adding some kind of spacers (could be washers or printed spacers) between the Kinematic Mobile Mount and the Pen Mount itself. 

  • This gives the pen holder space so it does not catch and hangup on the Kinematic Mobile Mount. 
  • Kudos to V1E forum member Jonathan Jones (@Jonathjon) for catching this and pointing it out. 
  • Below are photos of that in action, using washers as the spacers:

 

NOTE: June 8, 2023 — improved new release, v4.1, accomplishes two goals: 

  • The pen is located closer to the center point of the LR3's router (less offset from the cutting bit)
  • The offset distance is equal in both X and Y axes: ~52.043 mm for each. That's from the center of the router bit to the edge of the mount where the side of the pen rests. To calculate your actual offset, be sure to add on the radius of your pen body. See example below. (For anyone curious, the 45-degree diagonal measure of offset from router bit center to the edge of the holder where the pen body rests, is ~73.6mm.) Having X and Y offsets be equal hopefully makes it a bit easier to handle coordination between drawing and cutting in the same project. (Note: prior to May 14, 2024, the example graphic had an incorrect method of calculation. As of that day I caught the error and fixed it.)
  • NOTE: April 9, 2025 — was asked about offset for use with the newer main mount for LowRider v4. If one is using a Sharpie marker, which has a radius of about 6.14, the offsets for using this with the LR4 mount are: 
    LR4 X offset = +84.44 mm
    LR4 Y offset = -20.79 mm 
    Also note: if your pen has a different radius, then the difference only affects the X offset. So if your pen's radius is 4.14 mm (2 mm's less than the Sharpie), you'd subtract 2mm off the LR4 X offset, which was +84.44 mm, but now would be +82.44 mm. Since the offset can vary a small amount depending on several factors, if your project demands precision, then verify the offset before trusting it. This other listing of mine can help with verifying: https://www.printables.com/model/1241061-for-lowrider-or-any-cnc-printable-pin-pointer-tool 

IMPORTANT ASSEMBLY TIP:

  • Insert your two zip ties through the pen holder, before attaching the pen holder to the Mobile Base from the linked other listing!

Diagrams showing the X & Y offsets, and an illustration of calculating offset with a common Sharpie marker:

Note: You can also use the same formula to calculate offset when your pen is a different diameter, or if you have altered the diagonal offset by use of washers/spacers, etc. Here's how it's calculated:

Diagonal offset of the Kinematic Pen Holder, when no pen is present (from center of LowRider's router bit): 73.6 mm

+ Radius of a Sharpie pen: 6.14 mm

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 

Total diagonal offset with Sharpie pen: 79.74 mm

 

Using the Pythagorean Theorem (a² + b² = c²) we know the hypotenuse, so we can work backwards to get the sides. Since we know a = b (i.e. also a² = b²), we can rewrite the equation as: a = c/√2
or: a = 79.74/√2

So:
X offset = 56.38469473 
Y offset = 56.38469473

PS: in a cell in a Microsoft Excel spreadsheet, the final formula is written as:
= 79.74/ SQRT(2)

 

Here's a helpful video I made about this (the video shows older v4.0): 

OTHER COMPATIBLE TOOL HOLDERS INCLUDE:

Print, attach to the Mobile Base in the listing above, using three (3) screws and nuts, M3 x 16mm.

Install a pen using zip ties. Attach this and its Mobile Base to the Fixed Base on the LowRider v3, and draw something. Post results in the comments here.

 

Change log:

  • May 14, 2024 — Corrected the calculation of the X and Y offset when a Sharpie pen is in the holder (X and Y offset from center of the cutting bit of the LowRider to the center of the Sharpie pen). Updated graphic with this info. 
  • June 8, 2023 — improved new release, v4.1. See above.
  • May 18, 2023 — initial release, labelled v4.0 (because so many previous mixes).

 

My PayPal tip jar: https://paypal.me/design8studio  

 

Various LowRider 3 CNC remixes:

 

View all my models and remixes on Printables:

 

*Amazon product links are affiliate links.   

Tags