Da Vinci Webcam Mount
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
A shelf that attaches to the holes in the interior wall of a Da Vinci 1.0, 1.0A, and 2.0 printer, to mount a webcam…
- Rating
- 0 / 5
- Likes
- 3
- Downloads
- 28
- Makes
- 0
- Views
- 504
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Printer Parts & Upgrades
- License
- Creative Commons — Attribution — Share Alike
A shelf that attaches to the holes in the interior wall of a Da Vinci 1.0, 1.0A, and 2.0 printer, to mount a webcam (or other accessory).
Specifically, I am using the TeckNet C016 USB HD 720P Webcam, 5 MegaPixel, 5G Lens, USB Microphone & 6 LED (~$14, http://www.amazon.com/gp/product/B000Q3VECE ) because it has a close manual focus, and its own LED lights for when the Da Vinci's internal light turns itself off.
Specs:
*Dimensions: 4.504"W x 1.250"D x 3.595"H (each)
*Volume: 1.88 cubic inches
*Weight: ~0.04 pounds
Files:
*Shelf: PTW-00-1-PT-0195 (Mount, Camera, DaVinci).STL
*Prototype Shelf: PTW-00-1-PT-0195 (Mount, Camera, DaVinci) Proto1.STL - Small shelf to mount the camera in the corner, inside the rails, but my camera was too big to fit.
*Prototype Shelf: PTW-00-1-PT-0195 (Mount, Camera, DaVinci) Proto2.STL - Vertical shelf, but I didn't want to mount the camera sideways ultimately.
NOTES:
- .STL names do not match .SLDPRT name because Da Vinci will not print file names over 56 characters.
Print instructions
Category: 3D Printer Accessories Summary
A shelf that attaches to the holes in the interior wall of a Da Vinci 1.0, 1.0A, and 2.0 printer, to mount a webcam (or other accessory).
Specifically, I am using the TeckNet C016 USB HD 720P Webcam, 5 MegaPixel, 5G Lens, USB Microphone & 6 LED (~$14, http://www.amazon.com/gp/product/B000Q3VECE ) because it has a close manual focus, and its own LED lights for when the Da Vinci's internal light turns itself off.
Specs:
*Dimensions: 4.504"W x 1.250"D x 3.595"H (each)
*Volume: 1.88 cubic inches
*Weight: ~0.04 pounds
Files:
*Shelf: PTW-00-1-PT-0195 (Mount, Camera, DaVinci).STL
*Prototype Shelf: PTW-00-1-PT-0195 (Mount, Camera, DaVinci) Proto1.STL - Small shelf to mount the camera in the corner, inside the rails, but my camera was too big to fit.
*Prototype Shelf: PTW-00-1-PT-0195 (Mount, Camera, DaVinci) Proto2.STL - Vertical shelf, but I didn't want to mount the camera sideways ultimately.
NOTES:
.STL names do not match .SLDPRT name because Da Vinci will not print file names over 56 characters.
Instructions
- Print the shelf. Took ~2h:15m, and used 9.7m of filament. The settings I used are:
A. Quality: Excellent
B. Layer height: 0.20mm
C. 3D density: High (50%)
D. Supports: Yes - Carefully remove the supports from under the hooks. This is the only place they should have been created.
- Test fit the shelf in your printer, in the front left corner, where the door opens. See picture for interior holes to use.
- Test installation of your webcam.
- Remove shelf, and secure webcam to the shelf with a cable tie, or other method.
- Reinstall shelf. Nothing should touch the metal rails, since they spin.
- Route wire, out door handle opening or side vent.
- Adjust webcam positioning and focus.
- Print the shelf. Took ~2h:15m, and used 9.7m of filament. The settings I used are: