Air Fitting Hanger, Magnetic
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
This little magnetic hook lets you hang your extra air compressor fittings right on the side of the tank.
- Rating
- 0 / 5
- Likes
- 9
- Downloads
- 46
- Makes
- 0
- Views
- 442
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Tools
- License
- Creative Commons — Attribution — Share Alike
This little magnetic hook lets you hang your extra air compressor fittings right on the side of the tank.
Specs:
*Dimensions: 2.000"W x 1.375"D x 1.125"H
*Volume: 0.68 cubic inches
*Weight: ~0.03 pounds
Files:
*Hook for 18.5" diameter tanks: PTW-00-1-PT-0227 (Hanger, Air Fitting, Type D, 18.5in).STL
*Hook for 20" diameter tanks: PTW-00-1-PT-0227 (Hanger, Air Fitting, Type D, 20in).STL
Needed to complete assembly:
- QTY 3-6: 10mm diameter x 2.6mm thick Neodymium Magnets - http://www.dx.com/p/10-x-3mm-ndfeb-neodymium-magnet-circular-cylinder-diy-puzzle-set-silver-50-pcs-229283#.VOqSt9jnQYI (Description says 3mm thick, but are actually 2.6mm)
- Epoxy: For gluing in magnets
- (OPTIONAL) Plasti-Dip spray: Spray on magnets, to give them some friction.
NOTES:
- .STL names do not match .SLDPRT name because Da Vinci will not print file names over 56 characters.
- .STL files oriented for printing.
- Supports are needed to print the part.
Print instructions
Category: Tool Holders & Boxes Summary
This little magnetic hook lets you hang your extra air compressor fittings right on the side of the tank.
Specs:
*Dimensions: 2.000"W x 1.375"D x 1.125"H
*Volume: 0.68 cubic inches
*Weight: ~0.03 pounds
Files:
*Hook for 18.5" diameter tanks: PTW-00-1-PT-0227 (Hanger, Air Fitting, Type D, 18.5in).STL
*Hook for 20" diameter tanks: PTW-00-1-PT-0227 (Hanger, Air Fitting, Type D, 20in).STL
Needed to complete assembly:
- QTY 3-6: 10mm diameter x 2.6mm thick Neodymium Magnets - http://www.dx.com/p/10-x-3mm-ndfeb-neodymium-magnet-circular-cylinder-diy-puzzle-set-silver-50-pcs-229283#.VOqSt9jnQYI (Description says 3mm thick, but are actually 2.6mm)
- Epoxy: For gluing in magnets
- (OPTIONAL) Plasti-Dip spray: Spray on magnets, to give them some friction.
NOTES:
- .STL names do not match .SLDPRT name because Da Vinci will not print file names over 56 characters.
- .STL files oriented for printing.
Supports are needed to print the part.
Instructions
- Print the part, with supports under the hook, and in the magnet pockets. Print at 100% fill, for strength.
- Epoxy in magnets. I found it best to put a plastic shopping bag over each magnet, as I epoxied it, and hold them in place until it sets, to keep them from magnetically jumping to each other. It's easier to have a friend help with this.
- (OPTIONAL) Spray a couple coats of Plasti-Dip rubber spray over the magnets, to give them some grip on the air compressor tank.