Wearable Kanohi Kakama ( Bionicle Pohatu Mask )
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Cosplay-sized mask for Toa Pohatu. See below for instructions and the additional supplies you'll need.
- Rating
- 0 / 5
- Likes
- 35
- Makes
- 0
- Views
- 1,002
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Masks
- License
- Standard Digital File License
UNITY, DUTY, DESTINY!
Printing Instructions
For most printers, please use the halved version of the model. The full version is meant for printers with a print volume of at least 260mm x 260mm x 260mm. If using the halved version, you can mirror the model in your slicer to get the other half of the mask.
Both versions of the model require supports to print, I used Tree/Organic supports with “On buildplate only” turned on.
The print shown in the images was done with a 0.6mm nozzle at a layer height of 0.2mm, a 0.4mm nozzle should also work for this model.
What You'll Need:
Materials:
- Upholstery foam (For padding the interior of the mask)
- 1" wide elastic strap (About 12" long)
- Black Sheer fabric (A ½ yard will be more than enough)
- Black fabric, thick enough to block light (A ½ yard will be more than enough)
- Bondo, or whatever body filler you prefer (Only if using the halved model)
- Spray paint (The original Kanohi Kakama came in more colors than just brown, go nuts)
- Clear coat spray (Use one compatible with your chosen brand of spray paint)
Tools:
- Hot glue gun and glue sticks (Do not use high-temp glue sticks with PLA)
- Various grits of sandpaper (I used 80, 120, 220 and 400)
- Utility knife for cutting foam
- A Sewing needle and some thread (Preferably the same color as the elastic straps)
- Whatever glue works best on the plastic you print with (Only if using the halved model)
Optional:
- Black plasti-dip spray, or other brand of liquid rubber (for coating the foam padding)
- Sewing pins (Will make your life easier when fitting the strap)
Build Instructions
- Sand down the outside surfaces of the print(s)
- Start with the lowest grit sandpaper you have
- Sand until the layer lines are sufficiently smoothed
- Move onto the next grit of sandpaper
- Sand until you remove the scratches from the previous grit
- Repeat 3 & 4 until you run out of grits of sandpaper
- Clean the print(s) to remove any dust and debris
- If using the halved model…
- Glue the two halves of the mask together
- Fill the seams with the body filler
- Sand the body filler until it is smooth with the rest of the print
- Clean the prints to remove any dust and debris again
- Paint the model, clear coat it, and let everything dry. Follow the instructions for your specific paint/clear coat.
- See the attached image below to help with steps 6, 7, & 8
- Add the fabric to the interior of the mask
- Cut out pieces of the sheer fabric to fully cover the two eye holes (make sure to cut the pieces slightly larger than you need to make positioning/gluing easier)
- Cut out pieces of the thicker fabric to fully cover the three vent holes (make them slightly bigger just like the sheer fabric)
- Use hot glue to attach the fabric pieces to their respective locations'
- Add the foam padding
- Cut down three pieces of foam to fit in the three green spots shown in the below diagram
- Try to hold the foam pieces in place by hand and double-check the mask fits on your face before proceeding
- Feel free to modify/add more padding if you feel the padding does not fit right
- (Optional) Coat your foam pieces in plasti-dip/liquid rubber. This helps reduce light reflection from inside the mask.
- Use hot glue to affix your foam pieces in place
- Attach the strap to the mask
- Cut the strap down to slightly longer than you need
- Put one end of the strap through one of the mounting holes, and fold it over
- Sew along the fold to fix it in place (nothing fancy needed, any basic stitch will do)
- Put the other end of the strap through the other mounting hole, and fold it over (make sure the strap isn't twisted!)
- Use a pin or your sewing needle to temporarily hold the new fold in place, don't stitch it together yet.
- Be careful not to poke yourself during the next step
- Try the mask on to check how well it fits. If it feels too tight or too loose, remove the pin and adjust the strap accordingly.
- Sew the fold in place like previously
