1 / 3
Parametric Creality K1 Exhaust Fan Air Filter for Charcoal Pellets & Filter Cartridges of any size & type (OpenSCAD model) — image 1
1 / 3

Parametric Creality K1 Exhaust Fan Air Filter for Charcoal Pellets & Filter Cartridges of any size & type (OpenSCAD model)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Parametric case for any kind of filter - use charcoal pellets, or cartridges of any size and brand. OpenSCAD model

Rating
0 / 5
Likes
46
Downloads
210
Makes
0
Views
1,627
Reviews
0

Updated at source:

Model information

License
GNU General Public License v2.0

I designed this filter so that I can use charcoal pellets on my K1. The ventilation grid is optional and can be disabled (set parameter vww to 0), so that you can use filter cartridges of any size and brand.

I'd suggest to print this upright, such that the snaps are well connected to the case. Pick a sturdy material that can sustain some temperature and mechanical stress - e.g. PETG, ASA, ABS.

I've provided a rendered STL model with fixed dimensions, as well as an OpenSCAD model which you can freely adjust.

List of parameters

All parameters can comfortably be adjusted in OpenSCAD GUI. Here's what you can tune:

  • All case dimensions case[], including outside wall width cww
  • Lid length and wall width lid_params[]
  • Ventilation grid: hole width (hw), wall width of separating walls (vww), diameter of the round grid facing the printer (cgdia)
  • Case frame width (cfw) - minimum width of outside edge and ventilation grid 

 

Setting Parameters for Filter Cartridges

The parameter case[] is used to set the exterior dimensions of the case. These parameters include the wall width (parameter cww), hence your case dimensions should at minimum be the size of your filter cartridge plus twice the wall width in X and Z directions and once the wall width in Y direction (because the opening is on the Y side).

For example, say your filter cartridge is 80x90x20 and your cww is 2.5 - then your overall case dimensions should be at least 85x92.5x25.

This example does not include room for the lid (see below).

The lid opening is in positive Y-Axis direction and the lid also has a separately adjustable wall width parameter (the first parameter of lid_params[]). This wall width parameter also determines the height of the holding bar inside of the lid.

If you want to use the lid on a filter cartridge, add once the lid's wall width to the case's Y parameter to allow the lid to close properly.

From the previous example, we've got a wall width of 2.5 and filter cartridge of 80x90x20. This gave minimum case dimensions of  85x92.5x25.

Adding a lid with 2.7mm wall width leads to case dimensions of  85x95.2x25.

 

Automatically enabling the case fan

For the filter to be effective, the airflow needs to be guided through the filter (obviously). You can do this manually from the printer's control panel - or you may bake some gcode commands in the model you upload.

On the Creality K1, the fan with index 1 is the case fan. The command M106 P1 Sx sets the speed of that fan, with x being the parameter for the desired fan speed from 0 to 255. Now, the fan doesn't need to blow at full speed - it just needs to create enough suction to prevent that the airstream is exiting the printer through all the other openings.

I've been using a speed parameter of 20 and don't notice any plastic odor while the fan is running. If you want to apply the same settings, add the below command to your start gcode settings in the slicer. On prusaslicer, this setting can be found under the printer settings → custom gcode.

M106 P1 S20 ;case fan on

To turn the fan off again after the print, add this command to your end gcode settings:

M106 P1 S0 ;case fan off

Tags