VKB T-Rudder Mk IV Hydraulic Damper Mount
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
A block that attaches to the VKB T-Rudder pedals and allows you to attach a motorcycle steering damper to the pedals.
- Rating
- 0 / 5
- Likes
- 13
- Downloads
- 111
- Makes
- 0
- Views
- 1,536
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Video Games
- License
- Creative Commons — Attribution — Share Alike
Again a huge thanks to my buddy Qwarzz for help with the CAD side of things!
A block that attaches to the VKB T-Rudder pedals and allows you to attach a hydraulic motorcycle steering damper to the pedals. Improves the feel of the sprung motion, and enables unsprung usage as well, which is very useful for helicopters.
No permanent modifications to the pedals or metalworking required.
Designed for a cheap aftermarket hydraulic steering damper off of Amazon (https://www.amazon.de/gp/product/B093KYXGFY/). The joints are 8mm diameter, 12mm long holes, but since the T-Rudder primarily uses M5 bolts, I went with those and incorporated bushings into the design.
You will need to remove one of the bolts on the cam of the rudder, so that there's enough length on it to mount the damper. I used a 50mm, but 45mm should suffice. The bolts can be really stubborn to remove due to thread lock being used, but heating the bolt up with a torch allowed me to remove it.
It also uses the mounting slots for the rear pedal feet, so you can't have the feet all the way at the back, unfortunately. They need to come forward by like 1 cm or so.
Print list:
-Mounting bracket x1
-Damper bushing x1 (unless you source your own metal one)
Hardware needed beyond the pedals, damper and 3D printed parts:
-1x M5x45 or M5x50 countersunk bolt to replace the original bolt attached to the cam of the pedals
-1x M5x50 or M5x55 hex head bolt for the other end of the damper (not entirely sure on this, since I only had countersunks… used an M5x60 that doesn't fit in the hex hole, and it sticks out a bit)
-2x M5x20 or maybe M5x15 to secure the block to the pedal frame
-4x M5 locking nuts
-1x M5 washer
Designed to be a fairly tight fit, but there are slight variations in the T-Rudder Mk IV tolerances and of course printing tolerances. I had to hammer mine in, some might go in easier. Included are various different formats, including Solidworks, so hopefully editing the piece to fit your specific case isn't terribly hard.
Printed mine in PETG with 6 walls and 45% infill for extra strength. It's not as stiff as a metal block would be, but plenty stiff for usage. Prints fine without supports.
Build instructions:
-Disassemble the pedals until you have the cam detached (https://www.youtube.com/watch?v=4XyRHZKqsMc)
-Remove the left bolt, and replace with the M5x45-50 one. Might be stubborn, use heat if you can't get it loose otherwise. Keep in mind that which one is the “left bolt” will depend which cam profile you're using, since the cam flips around.
-Reassemble the pedals like normal
-Loosen the rear feet screws, and move the feet forward temporarily, so that they're out of the way
-Insert the M5x50 hex head bolt through the center hole on the block
-Insert locking nuts into the holes on the sides of the block, then insert the block to the rear of the pedals. Screw in the M5x20 bolts through the slots on the bottom.
-Slide the rear feet back into place (wherever you want them) and tighten them down.
-Insert the damper bushing into the shaft mount of the damper, then lower the damper on the front and rear bolts
-Add locking nuts to the damper mounting bolts and tighten down (don't overtighten, adds friction)