Qidi X-Smart 3 Nozzle/Hotend 25mm to 30mm Fan Adapter
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Adapter to upgrade the X-Smart 3 nozzle/hotend fan from 25mm to 30mm
- Rating
- 0 / 5
- Likes
- 29
- Downloads
- 201
- Makes
- 2
- Views
- 1,104
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Printer Parts & Upgrades
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
I made this adapter to allow me to switch the original, super noisy 25mm nozzle/hotend fan on my Qidi X-Smart 3 with any 3010 24V fan that is much quieter and seems to perform much better. I didn't want to use another 2510 fan as I'm sure it will still be louder than a 3010 fan, and I noticed that there is just barely enough space to squeeze in a 3010 fan in its place.
You will need a couple of extra screws to make this work, which you can obtain by “stealing” the screws from the rear printhead cover. There are 4 screws holding the rear back cover, take 2 of them. I leave the remaining 2 screws in a diagonal orientation. You will still need the 2 original hotend fan screws.
CAUTION!
Please be aware that replacing the default hotend fan might constitute to voiding your warranty with Qidi.
Please also be aware that using a 3010 fan will be a really tight fit with the front printhead cover and there is a chance that it might not fit yours perfectly. There is a degree of tolerance difference in between each printhead cover, and if you find that it is an extremely tight fit for your setup and it is really hard to reinstall the front printhead cover, then please do not proceed to avoid potentially damaging your front printhead cover.
Guide:
Use the 2 rear printhead cover screws to secure the adapter to the hotend fins onto the existing screw holes that held the 2510 fan. Make sure to screw the screws all the way through until the heads of the screws are flushed with the adapter. If they are not flushed, the screws might affect the functionality of the fan once it's installed. If you run into resistance, remove them are try again. You might also need to gently turn the screws as it “shaves” off some of the material of your printed part. If it is extremely hard to turn the screws, do not proceed and inspect your printed part. Make sure that the screws fit in properly.
After the adapter is secured to the fins, shimmy in the 3010 fan into the available space and make sure the two screw holes on the adapter line up with those on the fan. Note: Make sure that the fan wire is positioned away from the inner wall of the printhead, otherwise you won't be able to push the fan all the way into the gap and line up the holes.
With the holes lined up, use the existing black fan screws to secure the fan to the adapter. I've made the holes on the adapter smaller and tighter so that you can thread the holes with the existing fan screws and secure the fans without the need of nuts. However, please be mindful to not use too much force when turning the screws. You may either end up wearing out the holes, causing it to spin freely with no bite, or worse, snap the adapter in half.
After the fan is secured, go ahead and plug your newly installed fan to the control board on the printhead. Make sure that you tuck the fan wire properly and safely so that it is not sagging and touching the bed or worse, the hotend.
Print Notes:
Please print this adapter using heat resistant filament such as PETG or ABS/ASA as this will make direct contact with the fins of the hotend. While technically it is being actively cooled by the fan that automatically turns on when temps exceed 50C on the hotend, which means you can technically also use PLA, it is better to err on the side of caution and use a more thermally durable filament.
Print it any way you want, I did mine with the default 15% infill. You can go full 100% infill if you prefer. Print flat side down on bed with no support.
