1 / 4
Vertical LED Light Bars for the Prusa i3 MK3S/MK3S+ — image 1
1 / 4

Vertical LED Light Bars for the Prusa i3 MK3S/MK3S+

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Preliminary estimate for PETG

€3.89 – €4.76 net (excluding VAT)

For file: Light Bar Upright (Prusa)_0.15mm_PETG_MK3S_4h51m.gcode

This is an estimate for one file. You’ll confirm the exact price before ordering.

File and estimate settings

File used for this estimate

Average indicative estimate: €4.32 excluding VAT (range midpoint).

Weight reported by the author
46 g
Print time reported by the author
4.86 hr
Source material
PET
Estimate material
PETG
Estimate printer
Bambu Lab P1S - 0.4 nozzle
Estimate process
0.20mm Standard

Indicative estimate for the selected file only, based on the author’s weight and print time. File variants are not added together. The final price is calculated after file analysis.

Saved on this device.

Horizontally adjustable vertical LED light bars that don't cast a print head shadow on the build plate.

Rating
4.889 / 5
Likes
338
Downloads
1,361
Makes
44
Views
9,290
Reviews
36

Updated at source:

Model information

Category
Accessories
License
Creative Commons — Attribution — Noncommercial

I have a work light over the printer that casts a shadow of the print head and it was very difficult to see what was happening at the nozzle both in person and with the OctoPrint webcam. It's interesting that most of the existing lighting solutions are top mounted and would introduce the same problem so I created my own side lighting design.

Some design features:

  • The lights mount directly onto the side of printer frame in a similar way to the printers' rubber feet so you can slide the lights along the rail if you need to.
  • The light bar position is far enough out so the print head fan cannot hit them.
  • It is designed to use aluminium LED strip channel with diffusers so it looks a bit more polished (Each 13.2mm wide 210 long) but you can do this without the channel if you wish
  • The arm is hollowed out so you channel wires through for a cleaner look.
  • Gives very soft even lighting over the build plate
  • Taps into the printers power supply (Optional)
  • The hole at the back of the light bar is there in case you need to pop the aluminium channel out again

Parts list:

  • Aluminium LED strip channel with diffuser - 2 pieces at 13.2mm wide and 210mm long
  • 50cm of LED Strip
    • If you're going to use the printer power supply, make sure the voltage matches. In the case of the MK3S+ it's 24VDC
    • Otherwise just get one that matches the power supply you plan to use. Remember to check the current draw and make sure the power supply can handle the power required.
  • 2 wire cable; about a meter
  • Switch, I used an inline table lamp switch which I hide behind the printer
  • Cable ties to keep cables tidy

Build Tips:

  • Keep the quality high (0.10 or 0.15mm layer height) for the parts with the screw threads otherwise they may not fit
  • I had a lot of varying tolerances due to using build supports and parts would not always fit in my testing so I introduced a little bit of play between the fitted parts but you can glue them together if you want the joins rigid.
  • Leave some slack in the wiring underneath the printer in case you want to slide the lights back and forth along the frame.
  • Assembly:
    • When wiring, push the wiring through the support arm first then through to the upright part and then solder the LED strip. 
    • Stick the LED strip into the channel
    • You can then pull the wire back to remove any slack and allow the aluminium channel to seat.
    • Test the LEDs before cable tying everything in.
    • Cable tie the wiring to the back or the power supply avoiding the build plate carriage.

Tags