MCS DMAG / HELIX to Tippmann 98 Magazine
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
this was diffidently more complicated to make. but it does look nice I hope you guys can appreciate the time I put…
- Rating
- 0 / 5
- Likes
- 3
- Downloads
- 24
- Makes
- 0
- Views
- 387
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Sports
- License
- Creative Commons — Attribution
this was diffidently more complicated to make. but it does look nice I hope you guys can appreciate the time I put into this stuff.
this adapter should work on a couple of tippmann markers that uses the same feedneck mounting points as the tippmann 98 does
itchute movie link: https://www.bitchute.com/video/NZlRmetBmjad/
https://www.youtube.com/watch?v=tkegaAAC0ws
link to the Installation video of the Dmag magfed adapter
DMAG Bren LMG
https://www.thingiverse.com/thing:3937441
DMAG FG 42, P90 (Right)
https://www.thingiverse.com/thing:3937500
DMAG P90 (centered)
https://www.thingiverse.com/thing:3937473
DMAG FG 42, P90 (Right)
https://www.thingiverse.com/thing:3937457
DMAG Tall High
https://www.thingiverse.com/thing:3937511
DMAG Tall Low
https://www.thingiverse.com/thing:3937523
DMAG TIP98 normal
https://www.thingiverse.com/thing:4115746
DMAG TIP98 side
https://www.thingiverse.com/thing:4188333
DMAG TIP98 down
https://www.thingiverse.com/thing:4190624
DMAG cyclone side
https://www.thingiverse.com/thing:4227717
DMAG cyclone up
https://www.thingiverse.com/thing:4227722
DMAG cyclone down
https://www.thingiverse.com/thing:4227712
TMC Bren LMG
https://www.thingiverse.com/thing:3790969
TMC FG 42, P90 (Left)
https://www.thingiverse.com/thing:3919897
TMC FG 42, P90 (Right)
https://www.thingiverse.com/thing:3918514
TMC P90 (centered)
https://www.thingiverse.com/thing:3925118
TMC Tall high
https://www.thingiverse.com/thing:3925141
TMC Tall Low
https://www.thingiverse.com/thing:3925181
TMC TIP98 normal
https://www.thingiverse.com/thing:4112853
TMC TIP98 SIDE
https://www.thingiverse.com/thing:4188772
TMC TIP98 down
https://www.thingiverse.com/thing:4188787
TMC cyclone SIDE
https://www.thingiverse.com/thing:4224827
TMC cyclone down
https://www.thingiverse.com/thing:4226365
TMC cyclone up
https://www.thingiverse.com/thing:4226396
Print Settings
Supports:
Yes
Post-Printing
it can be a smart thing to melt in a iron or copper wire in the part shown in the picture. or print that section with a higher infill. at first was I surprised that it looked that is was not needed. but I had a failure on my second print so. keep that weak spot in mind.
for use of the 2 pins, just use 2x m3 bolts with a length of 12mm.
and of course 1 spring and 2 pins are needed to make the mag catch work.
Category: Sport & Outdoors