LayersFactory
Report model
1 / 12
Armor Case Raspberry Pi Mount for Prusa Bear — image 1
1 / 12

Armor Case Raspberry Pi Mount for Prusa Bear

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

6d6178

6d6178

@6d6178

Raspberry Pi mount for the Prusa Bear frame that works with heat sink type cases, such as the Sertronics Armor case.

Rating
5 / 5
Likes
37
Downloads
211
Makes
4
Views
2,105
Reviews
3

Updated at source:

Model information

Source
Printables
Category
Prusa Parts & Upgrades
License
Creative Commons — Attribution — Share Alike
DetailsFiles (2)Makes & comments (Makes: 4) (Comments: 6)Remixes (2)Collections (57)Related

This is a Raspberry Pi mount for the Prusa Bear frame that works with heatsink type a.k.a. Armor cases, such as the Sertronics Armor case or the Joi-It Armor Case or any case of this type. It works with Raspberry Pi 3B, 4, and 5. You just have to have the right case for the Raspberry Pi you're using.

If you use the original MK3S+ frame check out the version for the original Prusa frame.

 

Features

  • Works with Raspberry Pi 3B, 4, and 5

  • Works with any type of Armor-style case that uses M2.5 screws. Just google “raspberry pi armor case”. All of them are compatible, including the actively cooled ones.

  • Prusa Bear-style aesthetics

  • Short path between Raspberry Pi and the electronics case allows very short USB cables

  • STEP file available for easy remixing

 

Updates

V1.1 - 2024-03-26

  • Improved mounting hole overhangs

  • Replaced counterbore hole sacrificial layer with bridging layers

 

BOM

Qty

Description

Sourcing

1

Armor case for the Raspberry Pi (only top part needed)

Pimoroni, Amazon

4

M2.5x8mm Socket Head Cap Screws

Take from Armor case

1

M3x10mm Button Head Cap Screws

Aliexpress

1

M5 T-Nut for 2020 Extrusions (drop-in T-nuts or slide-in)

 

 

Assembly

  • Assemble the top part of the Armor case and the mount using the M2.5 screws so that the Raspberry Pi is sandwiched between them as shown in the picture below. You don't need the bottom of the Armor case.
     

  • Install the mount on the back side of the left vertical aluminum 40x20 extrusion (just above the electronics case) using the M5 bolt and T-nut. If you use a slide-in T-nut you will have to temporarily remove the top cap of the extrusion.

Print Settings

Print the part in the original orientation. The STL is pre-rotated for printing.

Use PETG or another material with a higher temperature resistance in case the Pi gets a little warm.

You can use the Bear print settings

  • Material: PETG (or any solid material with decent heat resistance)

  • Extrusion width: 0.45mm

  • Layer height: 0.2mm

  • Perimeters: 3 or 4

  • Infill: 20%

  • Solid layers: 4 or 5 top and bottom

  • Supports: no

 

Post-Printing

The four M2.5 holes are floating counterbore holes. They're closed so that they can be printed without support. You need to poke them through using an M2.5 crew or a 2.5mm drill bit or anything pointy. It's just a single layer.

Additional Credits

Tags

mountarmorbearraspberrypiraspberrypicaseraspberrypi4prusabearprusai3bearupgraderaspberrypi3raspberrypi4mountprusabearupgradearmorcaseprusabearaddonsjoyitraspberrypi3mount6d6178sertronics