1 / 6
Sovol SV08 BIQU Microprobe Mount (Stock or Neptune 4 Max nozzles) — image 1
1 / 6

Sovol SV08 BIQU Microprobe Mount (Stock or Neptune 4 Max nozzles)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Mount for the BIQU Microprobe on the SV08

Rating
5 / 5
Likes
40
Downloads
175
Makes
2
Views
2,159
Reviews
3

Updated at source:

Model information

License
Creative Commons — Attribution — Share Alike

NOTE: The pin on my BIQU Microprobe unscrewed itself after several prints - probably due to vibration. The pin can be unscrewed (see photo) and some loctite applied to the threads before screwing it back in. I've tested this a while now and it fixes the issue.

V20: For use with stock Sovol SV08 nozzles.
V21: For use with Sovol ‘hardened nozzle’ adapter and Neptune 4 Max nozzles. Note: The hot end carriage is very close to the bed when using these nozzles. Check your clearance.

This model would not exist without https://www.printables.com/model/947550-sovol-sv08-microprobe-mount - Read the instructions for connecting and configuring the probe there. The only difference in configuration for this mount is, in microprobe.cfg:

x_offset: -18.55
y_offset: 10.5

Also, in printer.cfg under [bed_mesh], set:

mesh_min: 5,15
mesh_max: 325,345

…to account for the new probe offsets.

The model is not a remix, but a complete new version that mounts the probe ‘backwards’ which I believe could give the mount a bit more stability? This mount uses the rear fan screw holes instead of using the print head mounting plate screws. 

Is it better? I don't know, but I wanted to try :)

Printing instructions:

  • Forget PLA. It may survive one print (which it did in testing, but after the print, it was soft and squishy).
  • Tested PC. At least my (cheap) roll of PC showed some creep when tightened for a couple of days, so I can't recommend that type of filament.
  • ABS, ASA - Tested and works! ASA tested more than ABS, currently.
  • Print with 45% infill, 0.12 mm layer height and 5 walls. This makes the part rigid.

To mount, you need: 

  • 2 pcs M2.5 screws (included with the BIQU probe)
  • 2 pcs M2.5 nuts (also included with the BIQU probe)
  • 2 pcs M3x20 (same kind of head as the BIQU screws - round hex head)
  • 2 pcs M3 nuts

Steps:

  • Mount the probe to the mount with the 2 M2.5 screws and 2 nuts. Apply threadlock (loctite)!.
  • Connect the cable (Make sure to follow the instructions in the model mentioned above to make the cable.)
  • Unscrew fan screws from the back (really short M3 bolts)
  • Remove hot end including heat break (2 screws top left, 1 screw middle front)
  • Fasten the mount by screwing the 2 M3x20 bolts from the front. Apply threadlock (loctite)!
  • Put the rear fan back on the now protruding M3x20 bolts.
  • Add a nut on each bolt. Apply threadlock (loctite)! Note: When tightening the nuts, apply some torque to the front bolts so they don't unscrew.
  • Remount the heat break with the 3 screws.
  • Remount the shroud - It may take some wiggling to seat properly, but it fits!
  • Done.
  • Run PROBE_CALIBRATE to calibrate your new probe mounting position :)

Tags