Counting matching models…
Print without supports, whatever type of filament you like. Unscrew the end of the SV08, slide Part A on, put the end back on, add filament, screw on cap. The cones should clamp on to the filament. There is a slot on Part A for a zip tie,…
//_UPDATE_// In putting together everything I found out that the umbilical plate that I originally put on was the smaller one. There are several different options for the plate. Ultimately there are 2 sizes and many options for what cable…
The original was a bit tight so i just moved the faces to make it fit better. made it so you can mount the thermostat in any corner.
Bucket for the side, is inserted into the existing holes, works with enclosure
I really hate how Sovol provided no provision for properly sealing off or even attaching the bottom edge of an enclosure in the shape of the base. So… I made these up, to give a surface for attaching some foam tape, and to provide some…
After removing the original cover, the contacts on the switch are open at 230 V. If you lift the printer at the bottom, you can easily touch them. This is prevented by the cover. M3 hammer nuts for 20x20 profiles and M3x10 screws are also…
I wasn't lucky with that nice hinges from nadir. It was because my workspace is so tiny that I can't let the doors open during PLA printing. With closed doors, the heatbreak gets clogged after max. one hour of printing because the cooling…
UPDATE: A working print head mount is now posted. My original was too high and would not home successfully. And Valerie Moore did a nice cleanup job on that if you are a perfectionist and want the nicest looking hidden surfaces! I have…
Print as shown in the picture (layer 0.12), without supports inside. Build of Materials: Switch OMRON D2F-5 (use NO) - 1pcs. Connector jst 2p 1.27 - 1pcs. Steel ball 5mm - 1pcs. ECAS04 (remove the rubber part) - 1pcs. M2x12 - 2pcs.…
Tired of plastic debris getting into your Z motor pulleys? Oh, didn't know that was a problem? Small bits of plastic from printing will make its way into your Z motor pulleys and fill up the teeth. This will cause stretching of the belt…
All the mounts I could find mounted the fan too close to the underlying surface when using the original feet, so I had to design my own.
This thing work as is but I still have to add assembly instructions so consider this a WIP. Improvements might also come along the way, I'm planning on making a less naked version of it. This mod allows you to install Creality K1 series…
The opening for the PTFE tubing has been enlarged to allow for the filament sensor connector to pass through while you are using a enclosure. Remix from the OG:…
I believe the Atomic shroud by Filip to have the best cooling of all the shrouds I've tested. Most other shrouds have poor output or the air stream is directed behind the nozzle instead of at the tip. This one is perfect except it didn't…
I printed this in PLA with 3 walls and 15% infill.
To help tidy wiring for external monitors etc on the SV08. This clip simply snaps onto any of the corner pillars and has various sized wire clips that can be attached. Upto two sizes of wires can be attached to each clip. Alternatively…
DIN rail mounting plates for the Sovol SV08 stock electronics. To be combined with these clips: https://www.printables.com/model/592735-din-rail-clip-voron-heat-insert.
Let me know if there is any issues you can find me @ https://discord.com/invite/jNqCQEhSYT This is the RC Version - I'm actively looking for testers and feedback, feel free to message me. <<<Non-Stock side panels use this version >>>…
Improved belt locking blocks for the stock SV08/Zero toolhead carriage. More adjustable, less of a pain to replace when doing toolhead/motion system maintenance. Improves belt parallelism to X beam. Use the strongest material you have…
These are some hinges for the top panel of the original SV08 enclosure (could probably be used with other printers). The panel should be removed when printing materials that need good cooling (like PLA). These hinges take advantage of the…
UPDATED: 2026-01-05 the V3 models below are the good ones... I have greatly improved the airflow and printability of the model. It is now possible to print with the front face at a 45 degreee angle to the build plate, which greatly…
A 45 degree remix of the filament runout sensor bracket. Puts less strain on the filament path as it enters the printer.
Instead of having the fixation against torsion on the right side of the body I used the same holes as the original sensor. Due to the low mount it is compatible with Eddy NG too.
This is a small poop bucket for the XOL-Metrx setup on the Sovol SV08. There is a non text and a text version. This could also work for a Voron 350.
Adapter to connect a 41mm diameter (OD) hose to the SV08 enclosure exhaust port. This is the diameter of the Mars Mate air purifier hose, so that the printer can be connected directly into the Mars Mate. If the hose connection is slightly…
Updates: 04/12/2025 - On popular demand, added a second circular gap to the left side of the toolhead, towards the exit path of the fan output, for the hot air to exit. I remixed the original model, which head very thin side walls (it was…
ich habe momentan keinen 120mm lüfter da also habe ich es geremixt das man auch einen 80mm radiator verbauen kann. Es gibt 2 Variationen eine die das Netzteil und das SSR und das Netzteil belüftet (v4) und eine Version die nur das…
If you find your toolhead board getting a bit too hot while printing simply add a 3010 24v fan! Edit: Fixed top so fully flat for better printing! Edit: Added vented version. Edit: Added the fan mount here too for ease. Edit: Totally…
Fully 3D printed Gantry for the SV08 MAX Note you can use this also with the stock motors but you will not put the extra bearings to support the shaft! ✅ What’s New This is the double shear variant of the SV08 MAX Front-access belt…
I didn't like the angle of the lcd screen on my Sovol SV08, so I modeled this bracket to change the screen angle. Updates Update 1: I included another version that should work okay with the enclosure lid. Update 2: Added a new model that…
I have seen quite a few mounts for the HDMI5 from BigTreeTech designed for the Sovol SV08, however, most of the ones I have tried would prevent me from opening or closing the doors for my official Open Enclosure , or hung well below the…
Mounting bracket for EBB36 toolboard on stock Sovol SV08 toolhead. Relocation of the front part cooling fan is not required. But trimming of the top of the stock toolhead cover is required to allow connection of the usb and/or CAN wiring.
Manual vent to allow some fresh air to go into the enclosure with doors closed. You can use it as front left or back right panel. Compatible with 5" and 7" display variant Shutter is hold on closed by 4pc of 6x3mm magnets. You will need:…
Print with standard settings but my preference is that this is printed in ABS or ASA. with 50% infill. V2 is honestly better where it has a more stable and flat profile. if you prefer V1 then this is still an option. I would recommend…
The opening of the original SV08 Sensor is wearing out very quickly, so i made a quick print, to guide the Filament through a short piece of PTFE Tube. Mount it with the stock screw. You need a PTFE Fitting (M6) and a short piece of PTFE…
Welcome to the turning drag chain gantry connection tower. It is the best way to give the cable freedom in turning by a moving toolhead. So check out the pictures and if you like it → build it!
EDIT 2026-02-21 More model updates: To increase the clearance from the lower left magnet, I have moved the mounting bolt to the right side hole. This allows for quite a bit more clearance from the magnet, and moves the metal bolt further…
⚠ Note: These parts are printed in ABS with tight fits . ABS shrinkage and warping can affect tolerances, so proper filament tuning is essential. We strongly recommend watching our filament tuning video before printing. Before you start…
The door stop that comes with the may has glued in magnets and the adhesive becomes weak and they pop put. This new stop uses 2 (8x2mm) round magnets. You can get them on Amazon or from Bambu Labs maker store. When printing be sure to let…
Wiring You must create or obtain a compatible cable for the LDO Nitehawk 36 USB connector in order to connect the BTT Eddy probe. A standard cable is not included and must be sourced or made separately. Mounting Hardware Use M4 × 6 mm…
This is a Remix of a remix of Txxx originals . I Liked Merp Derps remix but i used pla and the only issue i had was that was the left side would pop off and the original files came with holes for the 8mm standoffs but my hotbed came with…
this is a camera mount to swap the original camera of the Sovol Sv08 for the Kobra 3 camera. -tree support needed but just the 1 -no brim needed -uses original screw and cable -remember to re-pin the original wire to match the kobra 3…
This is an addon to the Sovol SV08 Max 150mm ZZ Tophat Replacing a corner with a version that has a Wham Bam the Clound holder. This model do not use or need any inserts, all holes are printed slightly smaller to allow threded screws to…
This is an addon to the Sovol SV08 Max 150mm ZZ Tophat Replacing a corner with a version that so you can place two 120mm fans on the side usefull if you want to move the enclusure fans so the printer can be closer to a back wall. This…
This is an addon to the Sovol SV08 Max 150mm ZZ Tophat The addon is a replacement corner that adds the holder for the BTT 7 Inch ver 1.2 screen. This model uses 8x4mm inserts for the fans all other holes do not and are just printed…
This is an addon to the Sovol SV08 Max 150mm ZZ Tophat This replaces a corner with an air slot and connector to move the air to a IKEA Förnuftig air purifier. You need a separate "IKEA Förnuftig" air purifier that you can get from IKEA, I…
After a year and a half the SV08 toolchanger mod has been released. In collaboration with DraftShift design, their Stealthchanger mod for the Voron 2 ( https://github.com/DraftShift/StealthChanger ) has been adapted to the SV08. Due to…
I have change the bottom for the orignal BigTreeTech cables
This mounts in place of the coupler mount on the top of the SV08 Max to utilize the BTT Filament Smart Sensor V2 SFS.
This bracket mounts the Infinityflow S1+ to the right side of the Sovol SV08 Max. It uses the existing M3 holes on the upper frame (normally used to mount the enclosure). Longer M3 bolts than used for enclosure will be needed. M3 bolts…
Used extended screws to remount fan. And snipped out the bullseye on the hotend shroud
This should adapt a removable A1 nozzle into a SV08 toolhead. It involves making a semi permanent modification, as you have to cut off the oval that the original nozzle screws to, and sink the 2.5mm heatset deeper into the backplate, then…
I made this simple exhaust hose adapter for the Sovol SV08 with the OEM enclosure, that comes with a 9025 fan. I wanted an adapter for 75 mm (3 in) hoses to save space. I couldn't find one, so I ended up making one. It uses 6x3 mm magnets…
I modified the model to accommodate the Bambu Hotend. I also added clips for better support. Material: PETG Marble White by nobufil Variable layer height 0.22-0.36mm No supports The item in the photos is not the final model; I made a few…
I initially printed out the spool holder panel and slider along with the right side corners. Everything fit great, printed panel with ASA and slider with PETG. Made the slight redesign to remove the risk of catching anything on the…
My Klipper screen was flashing red with a warning on the MCU temp. I have the Noctua fan upgrade yet after 20hrs of printing ABS the MCU ws getting hot. The electronics box was almost too hot to touch. I made these blocks to lift the…
Thank you at Nadir's team for these ultra top handle and stoppers ! Modified handle in order to make them fit on a flat plexiglass surface. All other files are on original model page.
Hi Guys. This is a printable frame to get more space between gantry and Original Panels. In my case i used a 6mm Isolation foam. Covered under the steelcovers. Anyhow, this gives you more Space for even bigger Isolation on your panels.…
This enclosure kit designed to store and print fiament spools, and I'm planing to design integrated dryer. I use cheap skateboard bearings and cheap 8mm rod. Bearings like this:…
This is a fix based on @Nadir's original model, based on the edit by @jkressin_272815to make them fit a physical printer
Remember in Star Trek when they divert power to other parts of the ship to survive? Me too! I am the Captain now. Maybe I’m Scotty. Either way, we’re going to make it. ABS doesn't use parts cooling so it infuriates me, waking up to ruined…
For T-Nut 2020 fasteners, you can either print them or buy them
Hey Guys, i am voronizing my Sovol SV08, for this i build the A4T Toolhead with the CNC Crossbow Filament Cutter. To Use this Cutter, there was no Model for a fitting Depresser Pin to actuate the Filament Cutter. So here we are, i made…
This is an updated/remix of the 3Dprintdemon's filament bucket and brush holder. The height has been raised to match the bed height of the Mandala Roseworks bed in the Sovol 08.
This is a new backplate and parts to fit the orbiter 2.5 into a Solvol SV08 printer. There are a few things that you will need to buy for this upgrade. will need 4x 4x5mm magnets https://www.amazon.com/dp/B075PMZ1J5 will need brass…
This is a fan mount I made for the SV08 using the original holes from the bottom cover. It is means for an 8010 fan (8015, 8020 would work as well if you have high enough feet). It was just printed in PETG-CF. I used standard fan screws…
I built a small cleaning bucket for perfboard instead of a silicone or brass brush since Eddy-NG needs a perfectly clean nozzle. It works 99% of the time and works much better than a silicone or brass brush — at least for me. You need a…
After switching to a bottom spool mount, I experienced some drag near the stock PTFE tube guide depending on the toolhead position. I redesigned the entry angle to minimize resistance and ensure a smoother filament path. The dimensions…
Shortened the original stock Sovol wiring bracket to allow for more slack between the bracket and the toolhead.
Just a fast design in hope of using the sv08 hotend for something instead of laying in a draw
I have seen many people wanting a microswiss hotend on the Sovol Zero/SV08 Max, so i sketched up an adapter to be able to use the SV08 version. Disclosure, my printer is currently not setup to use a Sovol toolhead, so this model is…
The belt tensioner simplifies the adjustment of belt tension X Y It is advisable to put washers under the bolts Timing belt pulley insert from the profile side M3x30 - 2 pcs M3x20 - 4pcs
After I accidentally ruined both mainboard and toolboard by moving X beam towards myself too fast I had to revive my SV08. this set-up allows to use almost all of original wiring, excluding mainboard-to-relay wire to control bed heating.…
This is an addon to the Sovol SV08 Max 150mm ZZ Tophat Replacing the back right corner with a version without any hole. Made after a sugestion from Doug Walker A great care was made to be able to print without much support, so hopefully…
Let the rear fan blow the air into the Sovol SV08 chamber. Use its original bolts and nuts to fix this diffuser inside. Of course the fan need to be flipped over to flow inside.
Tapa para hotend sv08 optimizada : Mas entrada de aire Reducción volumen al mínimo Mejor estética Personalizable ( combina colores al gusto ) Imprimir en PTG o ABS como mínimo Diseño optimizado de las piezas para impresión 3D ( no…
CHECK OUT MY NEWER AND PROPER VERSION HERE ! PARTS NOT TESTED all parts got "taller" for the additional height needed for the bigger belts - so not modified in bot directions to keep the belts kinda centered i'm working on a proper mod…
This is just my own fast 3d designed parts, and kinda backup for the stl and step files just in case.
Cartographer V4 probe mount designed for the Sovol SV08. Print: 1x (Cartographer v4 Mount) 2x (3.25mm tall ID 3.2mm OD 6mm Spacer) (these spacers slide on the screws that came with your cartographer mount) Probe Offsets (add these to your…
update 6/1/2026 - the more rigid ab mounts seemed to have resolved the x beam racking, however... unfortunately when i had first caded this up, i made some of the holes on the o.g motor and front mounts a little oversized. initially this…
GAS CONNECTOR SUPPORT WITH TILTING SYSTEM FIXING ON THE FRAME, THE ROTARY BLOCK INSERT M3 INSERT AND M3x6 CYLINDRICAL HEAD SCREWS
Print settings: No supports needed, just remember to remove the in-built supports before using. I used .2mm layer height and 10% hex infill. Prints on its face. Most hi-temp filaments will work, I used ABS. Inbuilt supports are marked…
SV08 MAX BTT SFSv2 MOUNT EDIT: ADDED 90º version where its angled to the side of the printer. This model is designed to fit the official Sovol Enclosure kit! No modifications required. Just add it to the open slot in the top metal plate.…
I Modified AT Brush Mount to work with Stock SV08 with no bed height adjustment. Works great and both versions I remixed and uploaded will work with a beacon/Cartographer set up. The deep version I uploaded is for someone wants the…
This has not been tested but should function fine to put the cable box from a Max onto the AWD stepper mount from an SV08 to build an AWD SV08 Max. Thank you Nadir for your efforts!
Summary Custom-designed spacer set for the Sovol SV08 Max to accommodate 2mm foam sealing tape installed between the chamber door and frame. This modification significantly improves heat retention by properly sealing the chamber while…
I have had a lot of trouble with the terrible filament holder on my SV08 - for some reason it has a very small diameter so typical filament spools will flop around and can get tangled - this fixes it pretty simply This is an adapter to…
I couldn't find something like this for my Wyze Cam, so I decided to make one. I know it's not nice to look at, but it works for my needs. Hopefully someone else finds it useful.
SV08 / Voron 2.4 Exhaust Filter that accepts the BTT SFS v2 filament sensor. This is ONLY the filter housing/shell. You still need to print the other components from Nadir. I might look at a modified version with a 9025 fan mount for the…
I was looking for something like this, but at that time, I did not find any, so I designed it for myself.
SV08 Goose Belt Purger System adaption mod to allow for Gantry Purging and nozzle wiping with no z movements needed when color changing. This mod allows for fitting the GBP (Goose Belt Purger) to the SV08 with the minimal amount of bed/Z…
I typically print big parts and having the build plate tends to bend and I could find any other model directly compatible with my setup, so I design it. I printed in PET-GF but you can use any other high temp material compatible with your…
