Counting matching models…
To build one, you need Attachment print (either pic center or hole center) Stock (m3, m3 w/ heatset, or 4-40 x 3/8 screws) in either normal or short lengths Matching buttplate to the stock chosen 2x 10-32 nuts (Imperial Mounting) or 2x M5…
V2, and a much needed upgrade of the original barrel collet system I made for the Xshot Longshot, using the same internal barrel collet as the Unicorn Wings Kit that can be found here: LINK . This still has the version of the collet that…
To build this - you will need one of each of these parts that are included (Choose one of the cylinders that is included) - along with a Bic Pencil spring (the ones that are hexagonal and look like this:) , and a toy screw or 4-40 x 3/8in…
To use, print both the left and right halves of either the “Low Profile” or the “Flared" versions. Both of these use the internals from the included X-Shot half length adapter, and both will require some cutting of the adapters…
Both parts are designed to be printed with no supports, Use a 4-40 x 3/8in screw in the front if the picc lock isn't staying in place. You will need to prime the blaster before installing. Don't have a printer? Order from OOD! Affiliate…
This needs 2x M3x6mm SHCS and 2x M3 nuts, print all parts without supports. Press the M3 nuts into the inside of the stock point, then screw the SHCS through the picatinny, through the stock point and into the nuts. This attaches to the…
Print with no supports, pull out the stock barrel and throw this one in. Don't have a printer? Order from OOD! Affiliate link !
This is a printable replacement magazine built mainly for the Diana, but it also has notches for the Worker Nightingale, and the Firerat (untested, also an uncommon blaster). It gravity drops from the Diana, but not the Nightingale. These…
These are drop in replacements for the top most red plates on the Dart Zone Outlaw. To remove your stock plates, undo the 3 screws, and then you will need to pull them out. There is a clip towards the back of the plates near the rear iron…
To install, start by butterflying the shell. Remove the original frontend. Drop in the new frontend and then button up the shell. For printing, I like to print with the front on the build plate, with some supports for the larger…
This is a drop in replacement for stock red faux-picatinny that is on the Dart Zone Max Outlaw. To install, remove the stock panels (save the screws) and press in the new panels you have chosen. Insert the screws into the screw ports. You…
This design is meant to be a press fit into the trapezoidal cutouts in the rails of the Xshot Longshot. This uses 2x toy screws (the normal screws that Nerf, Dartzone, and Xshot use to keep their blasters together). There are a ton of…
To print these, stand them up on the “back” of them (where the flat bit is) and have supports running up them where the letters are. I heavily recommend tree support. Be careful when removing the supports, as the “a” letter is fragile. To…
This is a folding variant of the picatinny stock found here : For printing I use tree supports for the parts in green, on the faces in orange. I would print these parts in mostly walls. between 6-8. This is going between you and the…
To install this spring spacer, open up the blaster and remove the spring/plunger guide peg. Slide the spacer over the peg, replace peg into blaster, then close up the blaster. Closing the blaster may be a pain as the parts have a tendency…
For use with any other collet in the ecosystem (Xshot Longshot, Unicorn) Printable with no support, if the overhang is giving some problems, you can use some. This is functional with the stock barrel. The stock barrel measures (incase you…
For how to use this jig, please watch the video here: Print in PLA or whatever plastic you don't mind being basically thrown away (this is a jig that will get cut) If you are having a hard time getting it to feed properly, shave a small…
Print both the left and right sides, this is installed by opening the blaster and pushing the left safety delete into the safety hole until it bottoms out. The left safety delete goes into the left side of the blaster if you were looking…
This is a blaster kit that I designed for the Nerf Rival Knockout. This blaster has a few variants. There is a single Spring Thunder shell variant, a single Flypoint shell variant, and a Double Barrel Flypoint shell variant. The links to…
This is a drop in replacement for the front end of the Rival Pilot. To install, put a 16x1.5mm o-ring (or any 1.5mm thick o-ring that fits) in the o-ring groove on the outside of the tube portion. Put this 3d-printed part inside the…
This is a full frontend replacement for the XYL KM9 Unicorn. This includes a Frontend, a Barrel Collet, and an extended Picatinny Rail. To attach the frontend, simply remove the screws from the stock frontend and push in the replacement.…
Press fit PCAR for Xshot Longshot, using Thanhtacles 's trivicus 1.0. It fits the lines of the blaster well.
This is a drop in replacement for the max stryker 2.0. It is not compatible with the stock barrel. Thanks to OOD for providing the Blaster to design for! Don't have a printer? Order from OOD! Affiliate link !
Use the stock mounting bolt from the original stock. Print fairly beefy. 6+ walls and good infill. Print with no supports.
Hardware is 2x m5x30 Button head cap screws and 2x m5 nuts. Print in the orientation shown below, with tree supports. There are a few options (0-flat degree, 1 degree, 2 degree, 3 degree) The angled rails are to allow you to use a red dot…
PLEASE USE THE V2 - IT IS SO MUCH BETTER: Can be found here: LINK This is a drop in replacement for the front end of the X-Shot Longshot's front end. There are many parts included, as there are many ways to use this mod. First, you will…
Use stock hardware. Replacement side picatinny, and a small plate that adds color to the side of your blaster.
A drop in replacement frontend for the Nerf Pro Torrent. This does not require any hardware, but does need a frontend piece and a collet. The barrel needs to be pushed in pretty hard to seat in the stock dart gate. Low profile Collet can…
Print both, use stock hardware for these. I plan to do a more streamlined version at somepoint. Don't have a printer? Order from OOD! Affiliate link!
All of these parts are self explanatory, the “color splash” models are just blank ones that fit the blaster and add color. These use the screws that come with the blaster to attach the stock rails. They are drop in replacements. Special…
Here is a Dev Kit for the collet I have used on SO many blaster frontends. I have made the license such that it allows for remixes and whatnot. I would LOVE to see this on blasters going forward, I just don't want people selling JUST the…
To install, Unscrew the mag base. Then screw the new one in (super simple). The extenders are somewhat untested, let me know if there are any issues.
An Updated version of this: Link , that now is able to be printed with no supports. This will work with the stock barrel, but will not have much of the barrel showing out the front of the blaster. There are two versions of the frontend…
This is just the center section of the Warp Saya with my edits to better restrain vertical motion of the center portion.
This mod requires the blaster to be opened, and replaces the stock collet that comes on the blaster. It does re-use the breach from the stock blaster - which is pressed into the “Replacement Internal Mate” as seen below. The collet can go…
This priming block is a drop in replacement for the stock one on the worker Seagull. I was able to It uses: 8x 623 POM bearings (the same ones that Alchemist and my Unicorn block use) 8x M3x10mm SHCS This does require support. Orient the…
This is a frontend, and will need to be printed with some supports. Orient it so that the 45° marks on the picatinny are so that the picatinny will not need supports. Use supports on the build plate only, and I like to use snug. This has…
A Bottom Loading Silly Shell Pistol. This is designed too look kinda like that one pistol from Kingsman, yea that one. I have included STEP Files. This is a first for me. Please don't steal my work. I've put more time than i care to admit…
I recently got access to a Makerbot Digitizer and am scanning in Pokemon toys from my childhood. Enjoy! Print Settings Printer Brand: Monoprice Printer: Maker Select Rafts: No Supports: Yes Resolution: .15mm Infill: 10% Filament: 3D…
This is a replacement priming block for the XYL KM9 Unicorn. This will replace the stock part completely. In terms of purchased parts, this will need 2x: 623 POM Bearings, and 2x: M3x8mm bolts. I have linked the POM Bearings below. Use…
This should be a simple print, use supports, I prefer the "snug" variety for this model. I have included a 3mf with the parts pre oriented. Hardware is minimal, requiring the following: 2x m3 nuts 2x m3x10 SHCS Print this with 5+ walls,…
I recently got access to a MakerBot Digitizer and this was my test and it went absolutely great! Print Settings Printer Brand: Monoprice Printer: Maker Select Rafts: No Supports: Yes Resolution: .15mm Infill: 10% Filament: Hatchbox PLA…
For this, you will need to have a Super SPAMF frontend, and this can work with the stock SPAMF barrel (about 4in) or any length you choose. To use the stock length barrel you will need the “Standard Length Collet“ file or the “Standard…
This is fairly modular, and can be assembled in multiple configurations. To use all picatinny (Top, Back, Bottom, two sides) the BOM is as follows: 1x m3x10mm thumb screw (this can be a normal m3 bolt, but will require tools to take the…
Inspired by Jan Štech and their Template For Electrical Diagrams , I have made a similar design to print for creating consistent Free Body Diagrams, as well as consistent Beams for strengths. Designed to be printed at a .2mm layer height.…
To install, unscrew the two screws that are in the pins - Remove the pins - Then pull the stock front end out. Then put the new one in, then put the pins in. Print it flat, like the others. No supports needed
This is a drop in replacement for the Nerf Rival Pilot to allow it to utilize flypoint shells, it has spots for O-rings (which are not strictly necessary, but will greatly increase performance and make it more consistent).The long tube…
Print them in their easiest orientation. The carabiner replacement is a tougher print, and may need supports. the grip shoe should use supports on build plate only. It has a fairly aggressive overhang. There is also a version that has…
Print this, its OK. Lowers FPS quite a bit, but no darts got stuck in my testing. It uses 4 m2 x 6mm screws (I used button head). Use at your own risk, like i said, its ok, but not great. :D
The top picatinny rail has sacrificial bridging, meaning there will be a layer of plastic in the holes that will need to be cut out. The side rails and cosmetic side bits need either 2 heatsets (m3x4x5) or 2 m3 nuts. These are because…
This uses the stock screws for the Kunlun rails. The side rails are the same as the Harrier, but the top are not (longer and have a weird fillet. Don't have a printer? Order from OOD! Affiliate link !
This uses the old N-Strike attachment point springs. Use a piece of tape to enclose the spring inside the larger shim section. This fits on the opposite side of the stock mag release, and will bottom out using the little offset section…
PLEASE USE THE UPDATED FILE THAT CAN BE FOUND HERE: LINK To use this, Remove the stock frontend, and place in the printed frontend. The collet will grip the barrel and cause it to move less around the priming block, as the stock frontend…
Take off the stock barrel lock (purple or brown, and will require some persuasion), and use a M3 Screw through the top hole to affix it to the blaster. This will not work with the stock barrel length, but the blaster in its stock…
Hi i forgot to post this when i made it. Its simple, needs no supports, uses 1x 4-40 to sinch the design together (it doesnt need this, but i added it cause it made me feel safer) Print like this print it with lots of walls (i do like…
This requires the removal of the stock orange ring around the tip. Mine was not glued in, and fell off before I designed these. Both use an M3 bolt to stay on and slide over the standard front end of the blaster (purple or brown). The…
These are all currently available results.
