Counting matching models…
Scraper to easily remove filament remnants from the print bed without removing the print bed Print Settings Rafts: No Supports: no Resolution: 0.15mm Infill: 25% Filament: Prusament PLA
I deliberately left space around the X-motor so that it gets enough air to cool down. The stepper motors get quite hot during operation. Required components: 2 x M5 10mm 2 x m5 t-nut Print settings: 0.4 Nozzle 0.2 layer 100% infill PLA or…
Container for Post-Its with the dimensions 76x76 mm. Maximum stacking height: 53mm. Enough for 5 individual Post-it pads. Left of it also a small box for paper clips, thumbtacks and Co. In addition, there is a holder for a pen with 1cm…
Parts needed: 2 x M4 screw 10 mm 2 x insert nut M4 Sponge cloth cut to 50 x 115 mm
Suitable for 120g of rice. Can be easily scaled in the slicer for individual portion sizes. Print settings: PLA 0.2 layer 0.4 nozzle no supports
I raised @Ondrashek's ingenious design by 25 mm so that the new height is around 30 mm between the printer and the floor. I did this mainly so that I could use @mayty plate holder .
After the Garmin Tempe is inserted, attach the holder to the backpack or jacket with paracord through the eyelet. Through the paracord the sensor no longer falls out. Version 2: Accurate fit More air slots for better measurement values…
Important: when slicing in PrusaSlicer, activate " fuzzy skin " on all walls. The default settings are sufficient. PLA print upright 0.4 nozzle 0.2 layer high fuzzy skin
Print twice per spool and attach to the spool with a few drops of super glue. Print settings: PLA 0.4 Nozzle 0.2 layer no supports
Bracket to attach the SIGMA bubble tail light to a GoPro Mount. The advantage of this holder is that the SIGMA Blaze does not need to be modified. The original side "wings" which serve as rubber holders of the original attachment, do not…
The wall mont is attached with two screws. The holes each have a diameter of 5 millimeters Print settings: PLA 0,4 mm nozzle 0,15 mm layer need supports
Print Settings: PLA 0.2 0.4 Nozzle no supports
Bracket can be stuck to walls or furniture with double sided tape Print settings: no supports 0.4 nozzle 0.20 mm
Print out left and right holder and attach to wall or bed with double-sided tape at the correct spacing. Slot width: 14 mm. The rounded edge belongs to the front, the sharp edge is the adhesive side. Print settings: PLA 0,4 mm nozzle 0,2…
Attach the printed holder to the monitor, car dashboard or furniture with double-sided adhesive tape. Print settings: PLA 0.2 0.4 nozzle brim
Webcam holder for the back of the MK4. Instead of the eufy adapter, other holders can also be subsequently attached to the basic holder with double-sided adhesive tape or superglue. Print settings: PLA or PETG organic supports 0.2 layer…
Print with 3 perimeter and 100% infill
Suitable for Deuter Strammer water bladders. https://www.deuter.com/de-de/shop/zubehor/c27998-trinkblasen 4 x 8x2 mm magnets are needed When slicing, add a print pause each time to insert the magnets. Pay attention to the correct polarity.
Required accessories: 1 x M5 Screw; 60 to 80 millimeters 4 x M3 12 millimeter 1 x M5 hot melt nut 4 x M3 hot melt nut 1 x M5 nut Locktite and plastic glue ¼ " screw Print settings: PLA 0,4 mm nozzle 0,2 mm layer no supports best 4 or more…
Spacer for Lupine SL AF 7 with GoPro adapter, so that the angle no longer adjusts or wobbles during the ride. Print settings: 0.4 nozzle 0.15 no supports
Print out left and right holder and attach to wall or bed with double-sided tape at the correct spacing. Slot width: 13 mm. Print settings: PLA 0,4 mm nozzle 0,2 mm layer no supports
All holders have a hole for a M3 wood screw. In the print files is an elevation for the wooden board. Print settings: PLA 0,4 mm nozzle 0,2 mm layer no supports Cactus:…
Print the parts twice and attach them to the Prusa Core One using double-sided tape on the bottom corners. This will allow you to quickly reattach the “ Prusament Core One Side Door for Filament or Toolbox” in the correct position.
PLA 15% infill no supports
These are all currently available results.
