Counting matching models…
Print the left and right hooks flat, angled edge up, and attach them with self tapping 3x12 tapered screws. Pick the body of four or two plier variant. Or both if you want (but be sure to print hooks for each). As the hooks are separate,…
Vase mode print of a storage crate. The model was optmised so vertical angles are no greater than 45 degrees off the horizontal. There are ofcourse some compromises in the design to decrease these angles, but I think the end result is…
My kids had been playing pirate in a laundry basket for days, and then complained their vessel was drifting off due to the lack of a proper anchor. Print with plenty of perimiters, as unavoidably, huge and heavy things will have be hooked…
Print the left and right hooks flat, angled edge up, and attach them with self tapping 3x12 tapered screws. As the hooks are separate, you can easily print different shape hooks to work with your pegboard.
Press fit two 5mm x 5mm magnets in the hole in the center. Mind polarity. If your printer's calibration is a bit off, you can glue those in place if the hole is too big, or drill them out with a 5mm drill if the hole is too small. I do…
Stylised washing machines for use in playmobil play. These were created as a tribute to Hans Grootveld , the founder and lead mechanic of Wasmachineservice Haaglanden . Print them laying down on the back for the best results. I used 0.12…
Print two hulls with the flat side down. Print one core with the side face down. On this image I marked the down face in blue. This way, the layerlines of the plug are 90 degrees to the layerlines of the hulls, providing maximum strength.…
Someone put a PS5 on a wishlist that had a 25 euro spending limit. I tried the original dummy ps5 by Angus L at 50% scale, but the assembly pegs were showing through the outside of the side panels, and the secret compartment required a…
Should fit most small pliers and cutters. Distance from the tip of the handle to hinge should be at most 100mm. Pliers should be no more than 15mm wide.
Usable for tools with a handle of at most 8.5mm diameter, and a shaft of 3.5mm. According to feedback these are sometimes sold as soldering aids, but I use them to pry supports out of bad models ;p Print the left and right hooks flat,…
Print the left and right hooks flat, angled edge up, and attach them with self tapping 3x12 tapered screws. As the hooks are separate, you can easily print different shape hooks to work with your pegboard.
I found a bunch of card holders, but all took ages to print and were overly complex and tough. This was inspired by Playing Card Holder by crazycollie, which on my printer with my profile took 10 hours and 70 grams of filament to print. I…
Compatible with medium size of IKEA product ID 505.177.60
Purpose I was annoyed when I had to open the top of the printer, and had nowhere to put the glass. And when I wanted to prop it open just a bit, I had to use a wedge of some sort. This new handle for the top glass serves three purposes.…
Print the left and right hooks flat, angled edge up, and attach them with self tapping 3x12 tapered screws. As the hooks are separate, you can easily print different shape hooks to work with your pegboard.
Replacement tile for 1980s european version of Guess Who? ( Wie Is Het? in dutch). Two part design for easy and flat printing inspred by Adrian Herbez @myMiniFactory I made a few changes to the original design to allow easier printing and…
Simple ring with exact dimensions based on your rolling pin, tolerances and desired dough thickness Print Settings Rafts: Yes Supports: No Resolution: 0.3 Infill: 100 Notes: I used PLA, but anything would work I guess. I also used 100%…
Mounted in the top front left of the printer. Requires a whole bunch of mounting hardware 4* m2x10 for the camera enclosure 2* m2x16 for mounting the camera enclosure to the bracker 1 * m3x18 for the axle 2 * m3x8 for mounting the bracket…
Simply screw it to the wall and plop the camera on top. There are slits in the mount to optionally secure the power cable to the mount, to avoid the camera being pulled off by the cable. The spacing of the screw holes is identical to the…
Important! I made this model for a friend without having access to actual penfill cartridges. I have used accurate dimensions provided to me, but I have not been able to actually test it with real cartridges. I used a printed one 😅.…
Should fit most common screwdrivers and drills. The weight of the handle doesn't matter as long as the center of mass is 150mm or lower. The stand isn't balanced by the screwdrivers in it, and will stay upright even with just one…
The perch is mounted to a flat wall using a bit of double sided tape. I included an alternate version of the mounting part with screw holes, but I'm not about to screw this thing into my furniture or walls 😅. Printing I included a picture…
Widest part of the screwdriver shaft can be at most 8.5mm. The top holes fits hand drills with tapered chucks. The narrowest part of the chuck must be at least 10mm diameter. Print the left and right hooks flat, angled edge up, and attach…
For situations where the grades are Accept, Minor revision, Major Revision and Reject. Printing You can print the first 0.7mm in one color and the rest in a contrasting color for pretty lettering. Do not use “Place on Face” to rotate the…
In continuation of our earlier work on unbiased coin flips during peer-review processes, we propose a novel solution: a one-sided coin. The one-sided coin ensures complete elimination of any potential bias while guaranteeing the absence…
I accidentlly printed this part for the wrong marble track, so I can't show it in context on the full Marble Run 2 model 😅
Peer reviews seem like a coinflip for a reason. These coins optimizes the review process by eliminating the tedious reading part. After selecting whether or not the current paper deserves a chance, select the appropriate coin, and flip!…
With multiple kids having identical drink bottles, they tend to trade (and steal) eachothers drinks. Printing a bunch of these marker rings in various colors helps avoid that issue. To install, slide it onto the cap before putting it in…
These are all currently available results.
