Counting matching models…
I took David6722's genious OTF Design and tweaked it a bit, I added places for screws, a pocket clip, altered the button and made a few more improvements. Prints very easily but may need some supports on the newly created overhangs. Print…
Charger for 18650 with spot for a 17mm x 27mm TP4056 charger / protection module. Underneath the 18650 holder there is a channel to run 1-3 wires from the charging module to the second pole and or out the other end of the charger. There…
compact Charger for 18650 with spot for a 17mm x 27mm TP4056 charger / protection module under the Battery. Underneath the 18650 holder there is space for the TP4056 charger / protection module. There are two channels that can accommodate…
Summary Slim RJ45 Ethernet Cap / Coupler that will save your ethernet cables and especially the plastic retaining tabs on your ethernet cables in bags cluttered with other cables. There is one open ended file to customize to your…
This is a compact box that holds and protects up to 3 condoms so you can safely carry them with you in your bag. The 2mm thick structural sides and edges of the box make sure the contents cant get squished, the front and back have 1mm…
Grabber to attach to 15 or 10mm OD pipe / Aluminium extrusion. The pivot holes are sized for 2.5 mm pins / m2.5 screws, the holes for the pins for the spring are 2mm. The spring needs to extend to about 45mm at the maximum travel. Print…
This is a small and tiltable mount to mount a Camera to a Flatscreen monitor. The mount will fit monitors between 14.5 and ~40mm in thickness, as long as the top, front and back are relatively flat surfaces. The mount is just 40 mm wide,…
Adjusting Ring / Shaft Collar 8mm, 10mm using a M3 Nut and Bolt. Choose a 12mm bolt, 10mm may be sufficient. The 8mm one will fit around TR8 / T8 Spindle like shown in the picture. Print instructions Category: 3D Printer Parts Summary…
Wire Bender using 2mmx 9.5mm metal pins. The retaining Holes for the pins are undersized and the pins will have to be press fit or heated up. This design was inspired by thing:4162219, but i added an adjustment for tool stick out as well…
This is a tool to purge air from radiators. It fits on 5mm outside lenght square valve screws. This Prints without support, if you rotate the large flat surface towards the build plate. Print instructions Category: Tools Summary This is a…
Tree Overhang test for both 90 and 60 degrees overhang to test cooling / overhang performance in 4 directions. The model has a built in base to make sure it is not dragged off the build plate. The Base is also chamfered for easy removal.…
How about I make this: ● Into this: ♥? Lenovo Thinkpad TrackPoint nub Replacement. Compatible with “Low Profile Soft Dome” keyboards (for example: Lenovo T450) If you are not sure which one you have, check out this Reddit post . It will…
Fan duct for adapting a 40mm fan to one 10mm OD hose, the fitting has an OD of 12mm and a length of 5mm. Hole spacing is 32mm, screw holes are 3.2mm in diameter, the counter bore is 5mm in diameter. Perfect for high-pressure 1U server…
The Tower of Hanoi is a mathematical game or puzzle. It consists of three rods and a number of disks of different diameters, which can slide onto any rod. The puzzle starts with the disks stacked on one rod in order of decreasing size,…
Squeegee Holder i made for my bathroom. Minimum distance between the two pegs is 30mm, the flared heads have a minimum distance of 26mm. The Holder is angled by 5° so the Squeegee slides back rather than forward. Use double sided tape to…
Bit Holders specifically for long bits with the large retention cutout The models requires some flexibility, so PETG or another less stiff material is recommended currently, 7 - 11 piece versions are included.
Air Pump Oil Separator for pumps like the ones found in refrigeration units. It catches oil in the air that is being forced up through holes with alternating location and allowed to drip back down the air line once the compressor is off…
Air Assist / Smoke Assist / Air Nozzle for K40 Laser. Will fit on a standard 26mm OD laser Head and is held in place by two short M3 Bolts. The nozzle has an inlet port designed to fit a 6mm OD PVC tube. To make a smaller opening for the…
Artillery Sidewinder X1 dial indicator holder for bed leveling / mesh bed leveling bolts onto the stock fan position, the gauge is held by two small zip ties. Revision 13.5.2020: cosmetic changes Print instructions Category: 3D Printer…
Can be attached to one side of a FFP2 Mask and hooked to the other to take the stress off the ears. This hook is designed to always stay attached to one side and be easily unhooked from the other. The strap is ~100mm long
Fan duct for adapting a 40mm fan to two 10mm OD hoses, the fittings have an OD of 12mm and a length of 5mm. Hole spacing is 32mm, screw holes are 3.2mm in diameter, the counter bore is 5mm in diameter. Perfect for high-pressure 1U server…
simple work piece holders for laser cutting, 3 pieces meant to be glued together, with a hole for a screw Print instructions Category: Tools Summary simple work piece holders for laser cutting, 3 pieces meant to be glued together, with a…
Adjustable (voltage limit, current limit) PSU DC/DC converter PSU power supply and display box This is a case for a XL4016 based buck or boost converter that accommodates wheels to set the voltage and current as well as a spot for a…
Sodastream Crystal Caraffe color coding ring Has chamfered corners and a rounded off opening for quick and easy Printing and installation. Just clips onto the carafe with a bit of force. Print instructions Category: Kitchen & Dining…
Bearing Ring for 6mm Airsoft BBs The two parts can be snapped together after filling up one side with Airsoft BBs. Depending on the accuracy of your printer you may need to deburr or file down some of the mating edges. This is only usable…
Logitech C270 cam mount for Stepper Motor (compatible with Sidewinder X1) 2 M3 nuts and 3 M3 cap head bolts are required. To mount the Webcam, you have to take off the standard stand. To do this, remove the elastic cover on one of the…
Stand for 2.5" und 3.5" HDD Platters for use as Mirrors 1 M3 bolt and nut is required. Suitable for 20 mm (2.5") and 24.7 mm (3.5") ID Platters Print instructions Category: Bathroom Summary Stand for 2.5" und 3.5" HDD Platters for use as…
Clip-On Serial Programmer using a 4 row JST-RE or DuPont PH connector and a small torsion spring (up to 8mm OD) and a 2mm hinge pin Print instructions Category: Electronics Summary Clip-On Serial Programmer using a 4 row JST-RE or DuPont…
K40 lasercutter X axis smooth Idler for 6mm belt designed as a direct replacement for the original toothed nylon idler with a tight press fit onto the bearing and a holding lip taken over from the original. Print instructions Category:…
K40 Lasercutter X axis carriage rollers designed as a direct replacement for the original nylon rollers with a tight press fit onto the bearings and a holding lip taken over from the originals. Print instructions Category: Parts Summary…
light cone for sofirn sp32a flashlight The flange is 23.6mm in diameter and has a length of 22mm. Print with a high temperature filament and keep the flashlight on a low setting. The light cone is 150mm long. Avaliable in .4mm and 1mm…
This is a replacement clasp for nylon carabiners often found as a lightweight alternative to Aluminum one on e.g. outdoor gear. Print instructions Category: Organization Summary This is a replacement clasp for nylon carabiners often found…
Visual Studio Debugging Keyboard This is a Keyboard for debugging control in Visual Studio. It features buttons for build-run, stop, rebuild, step over, build, step into and step out of. It is designed around an adafruit pro trinket.…
leveling directions for Sidewinder X1 and printers with same hand bed leveling screws Print instructions Category: 3D Printer Accessories Summary leveling directions for Sidewinder X1 and printers with same hand bed leveling screws
18 mm OD Buttons with Voronoi design and 3 holes for attaching, Chamferred on both sides, prints without supports, also features a recessed area on the front
Box to store 20 of the Filament Samples found at prusaprinters.org/prints/49734-customizable-filament-sample/files The model includes a lid that keeps the samples in place. It is printable without any supports
Stirrer for a 6mm Shaft, 45mm Outside Diameter, 45° Blade Angle, most suitable for viscous Fluids I use it to mix polyethylene glycol granules into water
This is a cover for the bus connectors on HP common rail PSUs. It slots over the PCB and has a cutout that can accommodate two XT60 Connectors stacked on top of each other. Additionally, it has a hole for a 13mm* 8,5mm switch to be able…
lens cap for sofirn sp32a flashlight to prevent scratches. The flange is 23.6mm in diameter and has a length of 22mm. Print with a high temperature filament and keep the flashlight on a low setting or off.
These are all currently available results.
