P
PrintablesShawnvanlan
Golf Divot Tool
Golf Divot Tool
- Downloads
- 1,868
- Likes
- 203
- Rating
- 4.75
All models
Counting matching models…
P
PrintablesShawnvanlan
Utility Knife V2
Robust Utility Blade Knife, print in PTEG or ABS, Revised Design
- Downloads
- 988
- Likes
- 140
- Rating
- 4.95
P
PrintablesShawnvanlan
Tub Drain Hair Trap
Tub Drain Hair Trap Print instructions Category: Bathroom Print Settings Printer Brand: Prusa Printer: Prusa Clone Rafts: No Supports: No Resolution: Any Infill: Any Notes: Scale X Y & Z separately to fit your Drain Size, Make Test Prints…
- Downloads
- 785
- Likes
- 82
- Rating
- 4.7
P
PrintablesShawnvanlan
Soap Holder
Simple Soap holder, much cheaper than purchasing in a store.
- Downloads
- 619
- Likes
- 47
- Rating
- 5
P
PrintablesShawnvanlan
X Stepper sleeve wire clamp
Clamp that retains X Stepper wire and sleeve. Eliminates bending action when Z travels up and Down. Print instructions Use 3mmx10mm screws with 3mm hex nuts. Requires large Zip tie to fasten to Motor.
- Downloads
- 342
- Likes
- 53
- Rating
- 5
P
PrintablesShawnvanlan
Upper MK3S Fan Bracket
Upper fan bracket that hides Extruder Wires. Uses original hardware, thread rear screw all the way in before install, this prevents pinching wires. Use ball end hex wrench. Prints perfect. Fits great. V2 is more refined.
- Downloads
- 250
- Likes
- 24
- Rating
- 5
P
PrintablesShawnvanlan
Travel Toothbrush Cover
Simple Travel toothbrush cover, PETG Gcode for Single print or 9. Print standing on End
- Downloads
- 243
- Likes
- 30
- Rating
- 5
P
PrintablesShawnvanlan
G26 Picatinny
Bolt on Picatinny Adapter for G26. Designed for Crimson Trace Rail Master CMR-206 or CMR-201 only. Uses 2- m2x5mm Stainless Socket Screws, nuts and carefully Drilling of Serial number Plate with 5/64" drill bit. Does not damage actual…
- Downloads
- 205
- Likes
- 26
- Rating
- 0
P
PrintablesShawnvanlan
Prusa MK3S .1 FS lever & Adapter
GCode for Original Prusa MK3S Sensor lever and Adapter PTEG, I had problems with IR sensor and Filament Jamming at run out. I Printed both of these and installed. Problems went away.
- Downloads
- 193
- Likes
- 9
- Rating
- 5
P
PrintablesShawnvanlan
Fidget Spinner Cap Threaded V2
I was not happy with all the caps I downloaded. This version will print on face with no supports. Larger than most other caps 1" diameter. Print at 1 to 1.5 resolution for accurate Threads (this depends on your Printer) Version 2 improved…
- Downloads
- 178
- Likes
- 9
- Rating
- 4.67
P
PrintablesShawnvanlan
Mazda USB hub removal tool
Mazda USB hub removal tool for removing & installing new CarPlay Android Auto hub, this tool makes it a 5 minute job. Remove passenger side center console panel, reach behind and press this over 4 latches. This tool save over 2 hours of…
- Downloads
- 177
- Likes
- 24
- Rating
- 5
P
PrintablesShawnvanlan
22 Mag Tool
Tested with Mark II 22 single stack magazine. May work with others, do a Test Print and see. Let me know. Print instructions Category: Sport & Outdoors Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No…
- Downloads
- 176
- Likes
- 33
- Rating
- 5
P
PrintablesShawnvanlan
Bat Spinner
Bat Spinner, use cleaned 608 bearing (no grease) one drop of light oil. Print 100% for best weight. Use these bearing caps to finish https://www.thingiverse.com/thing:2420043 Print instructions Category: Mechanical Toys
- Downloads
- 160
- Likes
- 17
- Rating
- 4.33
P
PrintablesShawnvanlan
200mm Drone Frame Vertical Stretch V3
Vertical 200mm Quad Frame. Using PTEG frame Weighs 73 grams not including Hardware. Uses 5" props and 2000 series Motors. Print 2 Side Frames, do not mirror, Bolt together with 2- 3mm x .5 x 35mm Socket Screw with 3mm and 4- 3mm x .5 x…
- Downloads
- 136
- Likes
- 12
- Rating
- 0
P
PrintablesShawnvanlan
Fidget Wheel Spinner
Use a very clean 608 bearing with Dry Graphite for lube. 2.75" & 3" Version. Use these caps with design https://www.thingiverse.com/thing:2420043 Print instructions Category: Mechanical Toys Print Settings Printer Brand: Prusa Printer:…
- Downloads
- 62
- Likes
- 13
- Rating
- 4.5
P
PrintablesShawnvanlan
Dillon Square Deal Handle Spacer
I like to Decap and Size brass before I tumble. Then I check Brass with a cartridge gauge. This Spacer keeps from pushing handle too far forward and picking up primer at station 2. Pre-checking brass saves from loading with powder and…
- Downloads
- 61
- Likes
- 3
- Rating
- 0
P
PrintablesShawnvanlan
You've Got Mail
My Version of Mailbox Flag, very easy to Reset. Tells you when You've Got Mail. Fusion 360 file included. I used extra 3mm hardware from my Printer Build. Best Larger V2 flag added, easier to see Print instructions Category: Household
- Downloads
- 49
- Likes
- 14
- Rating
- 0
P
PrintablesShawnvanlan
Bernardelli Model 80 Mag Base
Bernardelli Model 80 Mag Base
- Downloads
- 37
- Likes
- 5
- Rating
- 0
P
PrintablesShawnvanlan
Cat 6 pulling adapters
Cat 6 adapters for pulling data cables with with out plugs, Print on Smooth plate at slow speed.
- Downloads
- 37
- Likes
- 12
- Rating
- 4.5
These are all currently available results.