Counting matching models…
Designed this remix from the already great work of uscbutterworth & MP. I have a larger heat sink on my Raspberry Pi because it's overclocked so I wanted something that accommodated the extra vertical space. I increased the height of the…
Loved MartinDubois's clean design and thought DJHammy's remix of adding the snips portion was very clever, so decided to remix both to fit my needs. This will fit any 4040 V slot extrusion and will work on the right or left side of your…
Remix of a remix here. The original design is the Mini-Me V4 Lightweight Ender 3 Hot End Duct. The MinionD Ender 3 Dual Duct was a remix of that design which made some nice improvements to the original design like thicker duct walls and a…
Ring tray inspired by the classic Origami fortune teller! Or you might know it as the Cootie Catcher :) Printed without supports but I'd use a brim to keep it firmly planted while printing. Should be right around 3hrs at 0.28mm layer…
I designed this display for my Pocket to mimic and honor the design of the official Dock that Analogue sells. Print face down as shown in the pictures No supports needed Printed at 0.28mm layer height (approx 3hr) NOTE: This item is not…
Great design to work from. I prefer my screen at a higher angle so I reworked FredrikA's design to display the screen more upright. This shouldn't cause any clearance issues on most hot end setups, but please be careful and do a manual…
Needed something to help manage my cables after moving my extruder for my rear spool mount setup. I used the stock extruder mount location and added a simple clip for holding the wire loom. M3 hardware required.
This is 2mm thick but you can resize in your slicer of choice if necessary. Hope it helps fix your door!
Printed at 0.20mm with Protopasta Black/Grey
I designed this part to help diffuse the light on a new jewel faceplate I ordered online. The goal was to light the faceplate more evenly than the LED strips I have seen in the past. Additionally I wanted to use the existing LED on the…
4" Hairpin Leg I hope you enjoy and find a use for these beautiful hairpin legs. I needed a stand for my new PC to keep it off the carpet and I had already built a desk so I decided to model these legs to match. Worked great. Printed on…
If you decide to paint the controller ports on your N64 these will keep paint from getting on the pins. When complete they should slide over the pins in your controller ports to protect them and are easily removed via the ergonomic thumb…
I loved maunmaun's Sony PSP stand design from over at Thingiverse so I decided to make a Game Gear stand inspired by their work. I did remodel from the ground up to make it a little sturdier and fit the Game Gear's shell while also…
Got a new toolbox recently but it was missing the plastic latches to snap it shut so I modeled up some replacements. Perhaps this can help someone else in need :) Print vertically like in my photo without supports.
I recently found this old Samsung GX TV which was popular with gamers back in the day. It's got some pretty rad speakers and subwoofer and multiple RCA ports on the back which was pretty rare for a 13" CRT back in the day. Problem is most…
I got a new controller for my Nintendo 64 and someone at some point had tampered with the z button through the back holes on the underside of the controller snapping part of the inside of the controller and partially breaking the z button…
I designed this cover for my 3.5" hard drive in my Cooler Master NR200. I didn't like the look of the exposed drive so I decided to go for a cleaner look with some subtle accents. The cover fits my 2TB 7200rpm Seagate Barracuda drive so…
I primarily use 500g filament spools from Protopasta and I wanted a way to keep the spool centered in my Sunlu Heater Drybox when in use. Because the heater is designed for 1kg spools the smaller spools tend to move around a lot inside…
These are all currently available results.
