Counting matching models…
This is remix of www.thingiverse.com/thing:4679390 Baby Groot vase at 30% scale and taller cup for small flowers (made it taller with Meshmixer) I recommend printing groot_long_with_support.stl because there is 1 support cylinder under…
Simple test of parts flexibility of different thickness from 0.3mm to 2mm Print Settings Printer: Prusa Mini+ Rafts: No Supports: No Infill: 100 Filament: any any Category: 3D Printing Tests
Mount for Radiomaster Pocket and Hawkeye 3.5inch FPV monitor Requires screw (M3x12 works well) to fix monitor to mount. Mount snaps onto Pocket "To attach, put the bracket over the strap mount point on the centre or the radio at an angle.…
Print orientation ~45deg as shown in image. There are multiple version with 2 variables wall (H)height and (R)diameter show as red lines in image. Default is H=5.2mm. Diameter 3.2mm for PLA and 2.8mm for TPU print Most vanilla TPU print…
With Parametric Fusion 360 files. So stem could be easily modified to be taller or shorter No supports. Only brim needed for tall part Easy to disassemble Held by friction Stem must be printed in shown upsidedown orientation for it to be…
Shimano Altus Shifter Dust Cap Screw (tested and works) Two version: ShimanoAltusShifterCap_Printable: has different flat top good for printing (recommended) ShimanoAltusShifterCap_Accurate: has curved top face but it's hard to print…
GPS is hold by 2 tabs from the sides, it requires quite a lot of force to snap it in or out Version 2: Made it simpler to print and bowden printer by making print path more continuous It's more rigid GPS mount a bit tighter Print Settings…
Cinelog 35 SMA antenna mount at 45 deg. No supports. TPU. 3 perimeter Print Settings Printer: Prusa Mini Rafts: No Supports: No Resolution: 0.15mm Infill: 15% triangle Filament: Any TPU Notes: 3 perimeter for a stiff print. 2 perimeters…
Fusion 360 file included! It's a magnetic mount for TX16S and Hawkeye 3.5inch FPV monitor Short demonstration video: https://youtu.be/c1FKlvVu_cY Printing: Open stl, split to objects/parts (there are 2 parts), orient as in photo and…
Adjust rope length and leave 2 holes inserted on each side (photo1) for good enough grip or for extra grip insert the loop in middle 2 holes (photo2) Tested on 2mm rope (which measured with calipers is 1.8-1.5mm) Included fusion360 file…
Cable holder mounted with double sided tape to the wall for 3.5mm, 4.5mm and 5.5mm cables. It could fit bigger or smaller cables by heating up and bending. Fusion 360 file available Print Settings Rafts: No Supports: No Resolution: 0.2mm…
Bicycle bottle holder mounted on seatpost clamped with M5 screw. STL designed for 30.3mm seatpost diameter and 69.8mm bottle diameter. If needed for different diameter mount I included Fusion 360 file which is fully parametric. Model…
It's maple leaf sign required for novice drivers in some countries. 2 material print white base and green top I'll use PLA but PETG would be more durable in hot climates because PLA have lower glass transition temperature (50-80C) which…
This taller GoPro mount lets you tilt the GoPro more without hitting the battery and allows a lower angle since it's further from the props Print Settings Rafts: No Supports: No Resolution: 0.2 Infill: 100% Filament: Any TPU Notes: 10…
V2 Hawkeye mount design with Fusion 360 files No supports and no brim needed Held by friction Requires 3pcs M3x12 (2 screws for TX16S and 1 screw for monitor) 3 slots in radio mount currently has no use but it's left in case later mounts…
Thickened Fuselage01 modified using Blender to make it strong enough to be printed from TPU. Also increased motor mount thickness and made cut out for xt30 and motor wire to passthrough the front. Recommended version:…
I made this hangboard to be placed on top of high furniture, like a wardrobe, without the need for drilling or glue. Only duct tape is required to prevent it from sliding off the edge. To improve grip attach P1000 sandpaper using thin…
Custom fit ultralight Jordan toothbrush cover case for hiking only 1.23 grams! Could work with other toothbrushes if resized Fusion 360 file included Print Settings Spiral vase/Vase mode Slice gap closing radius: 0 mm Wall generator:…
Rectangular design of Iflight Quad Wrench makes it impossible to unscrew hex screws in continuous rotational motion therefore I created circular sleeve from flexible material which makes continuous rotation possible. Sleeve can be removed…
Stackable aerofoil shaped aerobar spacer kit 15mm - 75mm height, designed in Fusion 360 parametrically Currently for 31.8mm handlebars, and 50mm and 42mm hole spacing. Might be compatible with Profile Design. WARNING: DO NOT USE 4.4 GRADE…
These are all currently available results.
