Counting matching models…
This is a tablet mount for the Kove 450 Rally (Non pro version) that can be 3D printed. I am mounting a Samsung Tab A7 Lite in a rugged case with it. I printed with 3 walls and Gyroid infill. No supports or brim. I have printed the one in…
This is a tablet mount for the Kove 450 Rally (Non pro version) that can be 3D printed. I am mounting a Samsung Tab A7 Lite in a rugged case with it in the lower position or an AMPS bolt pattern RAM Ball with a Garmin GPS or a Motorcycle…
This allows you to remove your air filter and cover the air box of the Kove 450 Rally so you can hose or pressure wash the bike down and not get water into the carb and motor. You need a 256mm x 256mm print bed for this to fit. Do not…
These are Visors for the gauges on a Vanderhall Carmel. I printed them with PETG. They are a snug slip on fit. If they loosen up over time you may need to add double sided tape. If it is too tight to slide over you can heat the bottom…
For the Kove 450 Rally with the plastic tower. This mount allows a tablet or Apple Carplay unit to mount below the gauges and a RAM ball to be added to the top.
These mounts hold closet rod 1-5/16 in. Dia for ceiling mounting above a window. The extension on the bracket is likely no long enough for wall mounting and holding the plant pot off the wall. Works great for ceiling mounting. See…
These are Visors for the gauges on a Vanderhall Venice. I printed them with PETG. They are a snug slip on fit. If they loosen up over time you may need to add double sided tape. If it is too tight to slide over you can heat the bottom…
These are Visors for the gauges on a Vanderhall Carmel. I printed them with PETG. They are a snug slip on fit. If they loosen up over time you may need to add double sided tape. If it is too tight to slide over you can heat the bottom…
Vanderhall Carmel 3rd Brake light housing – This 3D Print file will only fit the Carmel model with the larger roll bar diameter not the Venice. It is designed to accept a standard Vanderhall brake light (Not included) to match the other…
This adapter will allow a small diameter flag pole like the Walmart $12 flag with pole to be larger and fit better in a 1" flag pole holder or mount like my Harker EDC Camper Flag Mount Recommend PETG for outdoor use.
This is a plate frame that fits Utah motorcycle plates and is made for the Kove 450 Rally. Note the utah plate holes do not line up with the holes on the back of the Kove 450 Rally. You do have to drill 2 holes closer together to bolt on…
This is a small tray to fit in the top of the center console of a 2020 or newer Land Rover Defender (without the fridge option) to provide easy access storage. It is a tight fit needs sanding around the top lip and deburring to make it…
This is a knob that slides over your glovebox key to hide the key and create a better looking knob that can be left in place. I printed mine in PETG. I pushed my key into it right after it was printed. It was a tight fit for the key. I…
This is a flag pole holder for the Harker Outdoors EDC Camper to attach to the top rail. It easily attached and can accommodate up to about 1" Dia. flag pole. (See adapter separate for smaller dia. pole) I recommend PETG filament for…
This knob that slides over your glovebox key (Which must be cut down) to hide the key and create a better looking knob that can be left in place. I printed mine in PETG. If your cut down key is loose you can glue the key in or just wrap…
Vanderhall Carmel Cup Holder Adapter – 3D print STL for a cup holder adapter slides into the existing small cup holder and offsets towards the inside of the vehicle a new larger cup, tumbler or flask holder with a hole size of 3.44 inches…
These are all currently available results.
