P
PrintablesScottieD369
Jet Ski Key
Jet Ski Key This was designed by a friend of mine that had me print it for him. RIP Zachary Raymark Category: Sport & Outdoors
- Downloads
- 127
- Likes
- 11
- Rating
- 5
All models
Counting matching models…
P
PrintablesScottieD369
SCD-40/41 Sensor Box
SCD 40/41 Sensor Holder Snap-In cover mount Sorry I had to delete old one and re-mod. This one won't break! In project fround HERE >>> https://www.thingiverse.com/thing:6275794 Category: Electronics
- Downloads
- 115
- Likes
- 7
- Rating
- 0
P
PrintablesScottieD369
MQ Sensor Holder
MQ Sensor Holder Category: Electronics
- Downloads
- 70
- Likes
- 2
- Rating
- 0
P
PrintablesScottieD369
Spy Cam Case
Spy Camera Case less than the size of a pack of cigarettes. Snap fit design! SUPER TIGHT! Triangle design! MUST REMOVE ALL SUPPORT!!! UNDER $30 !!!!!! Some soldering required for microphone uv super glue for antennae tape everything in…
- Downloads
- 64
- Likes
- 7
- Rating
- 0
P
PrintablesScottieD369
8CH Relay Mount
8CH Relay Mount Other Mounts Listed: 1 Channel Relay Mount: http://www.thingiverse.com/thing:1284047 2 Channel Relay Mount: http://www.thingiverse.com/thing:1285305 4 Channel Relay Mount: http://www.thingiverse.com/thing:1287530 This also…
- Downloads
- 47
- Likes
- 5
- Rating
- 0
P
PrintablesScottieD369
PunchDown Holder Keystone Jack
Just place in PALM of hand and punchdown wire. Saw various of these things from back in the day and NEEDED to make NEW CUSTOM! SOO WELL WORTH THE PRINT! Category: Electronics
- Downloads
- 42
- Likes
- 8
- Rating
- 0
P
PrintablesScottieD369
IEC Mount (snap-in)
AC Power IEC Standard C-14 Inlet Connector Snap-In R-301SN This design is like all my other type of snap-in's. They have to be recessed with a thin low tight fit with a border. Outside of the border you can have your thicker normal walls.…
- Downloads
- 30
- Likes
- 1
- Rating
- 0
P
PrintablesScottieD369
Castor Wheel 01
I needed a replacement wheel. Original was rusted on. Sawzaw couldn't work. Only a cut-off wheel would work so be careful. Compost Barrel Tumbler Seems like about 10-15 Pounds per square inch. I'm sure you can exceed 20+ but then you'll…
- Downloads
- 29
- Likes
- 5
- Rating
- 0
P
PrintablesScottieD369
Keystone Jack Modular Enclosure
Enclosure for Keystone Jack Harvest port from faceplate. Use UV super glue to hold in place. Then punch down wire. (Use my other project for help!) Punch Down Holder [ https://www.thingiverse.com/thing:5882502 ] Snap-in backplate. Mount I…
- Downloads
- 27
- Likes
- 2
- Rating
- 0
P
PrintablesScottieD369
U bracket for motorcycle handlebars
I friend of mine asked me to design one for him and print it so I thought to share my version. Category: Other
- Downloads
- 22
- Likes
- 5
- Rating
- 0
P
PrintablesScottieD369
Twisted Pair Cable Clip
For mounting Cat 5E or similar cable to a surface. This is a screw in type provide your own hardware. Give a solid hold on any communication cable! Can be used indoor/outdoor any surface. Got long runs of wire with big loops? Add one of…
- Downloads
- 21
- Likes
- 1
- Rating
- 0
P
PrintablesScottieD369
120VAC Outlet Holder
I've spent over a HALF ROLL of filament to get this to work! This is my famous snapfit recessed style outlet holder! I did put a little super glue along the edge of the inner as pictured to strengthen the bond! I would say you shouldn't…
- Downloads
- 17
- Likes
- 1
- Rating
- 0
P
PrintablesScottieD369
Electronic Foot 01
super glue to bottom of project Used in project https://www.thingiverse.com/thing:6443445 Category: Electronics
- Downloads
- 14
- Likes
- 0
- Rating
- 0
P
PrintablesScottieD369
PiZeroMount
Here's a Raspberry Pi Zero mount so that you can mount it to something else! Since nobody else had made one I had to design it! Because I had a project in mind that I needed the use for it! It's a tight fit but it will get in and be…
- Downloads
- 13
- Likes
- 0
- Rating
- 0
P
PrintablesScottieD369
Siren/megaphone revamp to Alarm Siren
I took apart a classic style horn to make it a security deterrent. Simply remove not needed parts and make solder connections as pictured and add a DC barrel plug. tape off with electrical tape the mounting screws. Came from Harbor…
- Downloads
- 11
- Likes
- 2
- Rating
- 0
P
PrintablesScottieD369
Raspberry Pi IoT
I am sharing with you all of these wonderful items created by this project! This project can be found here all instructions and code! https://www.instructables.com/Raspberry-Pi-IoT/ (please refresh hit enter sometimes links won't work?)…
- Downloads
- 11
- Likes
- 1
- Rating
- 0
These are all currently available results.