Counting matching models…
Scan of a Honda K24Z3 engine. This was a complete longblock, please not it has a few non oem parts made to swap the engine into a miata (oil pan, intake manifold, timing cover, and valve cover). I was scanning this for my own purposes but…
Scan of a NB mazda miata front subframe with control arms, rotors, hubs, spring, shock, and steering rack. Please note this is the super rare manual rack which is much smaller than the normal power rack. Scan is not complete but still…
This is a replacement gauge cluster for NB Mazda Miatas. With some slight tweaks to the design this would also fit the NA. The mount is for the 7" digital cluster from nexgenefi.com which has support for a wide variety of aftermarket…
This is a flange to bolt 1.5 inch pvc to a board or wall or floor. Category: Parts
This is a clutch alignment tool for NC Mazda Miata with a 6 speed transmision. Should also work for many ford duratec engines as well. Category: Automotive
This is a remix of a model originally made by yani05. I modified it to be 3d printable and not need the alumin craftworks bracket. You need m6 threaded inserts, m6 bolts, and one special ultra low profile hex head m6 bolt for the back…
This is a switch panel mount for a miata race car. If you have removed the lower part of your miata dash and want a way to attach switched, gauges, etc this is what you need. I originally 3d scanned the lower dash mount area and made this…
This is a spacer that fits between a lot of common inexpensive radiators and the stock mounts on the NA/NB Miata. You will need to print 4 of them for top/bottom and the anneal them. Category: Automotive
Scan of a miata front lca The scan isn't great. It was good enough for what I needed. I'm uploading it to be nice. You get what you get. You don't get upset. Category: Automotive
This is a plug for the differential of a FRS/BRZ/86/GR86. This is used to plug the hole the axle goes into if you are removing or installing a differential. I used this to test different differentials and remove/install them without…
If you use single use preservative free eyedrops and want to get more than one use out of each vial this is a holder and lid which will help. There is a base which is just a cup to hold the vial and a lid to put on top to help keep it…
This is a clip that fits onto the stock fuel rail of most K20 and K24 engines. From the factory there was a wiring harness that mounts to this hole. But if you have done a motor swap or a tucked harness then there are mounting holes in…
This is a "button extender" for the traction control switch on the ND Mazda MX5. If you are racing the car and forget to turn off traction control this part makes it easy to find the button. Category: Automotive
Printable gurney flaps for 9 lives racing wings. I found that it was best to print them at a 45 degree angle (see photo). This gives the best strength in the axis we care about. It actually prints really well in this orientation with a…
This is a scan of a NB miata subframe with a k24z3 engine, 6 speed transmission, and control arms. Please note this is the ultra rare manual steering rack which is much smaller than the power rack. Scan is not complete but still useful.…
This is a wall rack for longboard or skateboard decks. This was designed to fit just decks by itself without wheels/trucks. It might fit a complete board with wheels/trucks every other level. The arms attach with M5 screws. There is a…
This is a custom shock rebound knob for KW coilovers. This is for applications where you need a longer reach knob. You will also need to buy a 2mm L Hex key in whatever length you need. Cut off the short leg of the hex key and then use a…
This is a baseplate for a zero degree truck for a longboard. This would normally be for a board you want to setup for LDP - long distance pumping. To make this work you would need to have this file laser or plasma cut out of steel, then…
This is a tool for checking the rear caster on a C7 Corvette. Additionally you will need a 1/4 steel rod which is available from any hardware store. Category: Automotive
This is a zipped folder with marlin firmware for a Maker Select V2 (also known as Wanhao Duplicator i3) with a ramps gen 1.4 board. Here is the kit I used:…
Very simple mount to attach a yaw sensor to a 1.5 inch or 38mm roll bar or dash bar. Use hose clamps, be careful on how much you tighten them you can definitely crack the plastic.
Ok this is a 3d printed version of the machine that uses a vacuum to apply vinyl wrap to cell phones. Here is a video of it in action: In addition to the 3d printed part I needed to use a 1/8 pipe tap and a brass pipe fitting which you…
Steering column mount this steering column: https://www.speedwaymotors.com/Steering-Column-Mounting-Bracket-3-4-Inch-Shaft-1-25-1-75-Inch,461403.html This is made for the nexgenefi display but if you have basic cad skills this could be…
This model is brackets to attach limit switches to a genie screw drive garage door. I was trying to install RATGDO on my garage door but this screw drive door is considered dry contact and needs limit switches to work properly with apple…
This is a tool to spin the Miata 1990-1997 CAS sensor to bench test it. Put the tool in a drill and then spin it.
This is a backplate adapter for the wanhao/maker select 3d printer to adapt an 80mm fan. This file is a remix of another design which is intended for use with an external power supply (the xbox 360 PSU). If you are using the stock power…
This is a trickle charge port for an NB Mazda Miata. This replaces the key cylinder just behind the rear bumper. This is mainly for dedicated race cars where you can't open the trunk easily (on pins, or aero blocing it) making it easier…
This is a tool to help bleed the GM version of the Tremec TR3160 transmission. This came in the 2.0 and 3.6 motors in the Chevrolet Camaro, and the Cadillac ATS, and then this same slave cylinder was used in the Colorado and GMC Canyon.…
This is a scan of a super atv ez steer power steering unit. If you are trying to mount one of these this might help. It's not perfect but you didn't pay for it so be nice pls.
These are all currently available results.
