Counting matching models…
Here's the small pan/tilt I built around the Runcam Eagle 2 Pro (should work on most similar cameras) and used on my Sonicmodell Binary. See it in this video: https://www.youtube.com/watch?v=pUAvgBmgIEU You'll need two of these ball links…
These parts are shown in more detail in this video - Print the VTX mount with the slanted part, front end, down on the print bed. It prints with no supports that way. Trim the fuselage front so the mount slides in with some friction to…
You'll need to trim some foam from the canopy and glue the insert in place. I placed mine so the front of the insert is about 10mm behind where the air intake stops. Trim the hole a bit small at first then fine tune for a snug fit, it's…
This is a tray intended to make for a cleaner mount of the Walksnail VTX onto the Atomrc Swordfish. It fits into the fuselage using the stock nylon screw, and holds the transmitter, as well as the antennas. The transmitter is placed high…
When adding a damper to the Y axis stepper motor, the X-shaped plate under the bed hits the motor before the limit witch is reached. The solutions I found were to either move the limit switch, which costs some build volume and make the…
These are replacement "levers" for the sliders on the T16 and TX16S. Not being a fan of the short stock ones when using them for pan and tilt on my FPV planes, I wanted something longer. Andrew Newton posted a design for some thicker ones…
I made this to hold the Gitup F1 camera and a micro size FPV camera (I'm using the Micro Eagle here) on my Skyhunter. It uses the GWS S125 sail winch servo for a 360º pan, and a smaller servo for tilt. I use a Turnigy 380MAX that I had as…
This is a pan and tilt unit designed around Runcam's new HD camera, the 3S. It also holds a micro FPV camera along side the HD cam so the pan and tilt together. (I prefer using a separate FPV cam) The tilt servo will stick to the bottom…
This is my cooling solution for a BMG style extruder and V6 hotend combo. I made up this carriage for my EMT8 (modded A8), and needed a cooling solution for both the hot end and the parts fan. Initially I tried several designs and all had…
Here's a pan/tilt mechanism for the Foxeer Mix FPV camera. I'm uploading this now for the people that asked, but have not flown it yet. Once I do, I'll add a video here. Parts are rotated in the proper orientation for printing. I printed…
These are vented ESC covers for Sonicmodell's new twin engine FPV plane, the Binary. The stock kit includes some flat plastic covers with 3M tape for covering the ESCs. I wanted these vented ones to get a bit of airflow to cool the ESCs.…
Here's the pan/tilt mount I used in this video: https://www.youtube.com/watch?v=TARXprDY2DE You'll need some various bits of hardware to assemble it. The screws included with the Hybrid are a bit long, I used some little plastic washers…
This is the updated version of this thing: https://www.thingiverse.com/thing:2824974 Pretty close to the same design, but with the more enclosed case for the board built into the base. For the linkage, this was confirmed to fit:…
I recently bought a 12V 30A power supply from Zyltech to replace the old stock 20A one on my printer that ran rather hot. The Zytech one is much nicer, quiet and runs cool, but I needed a cover for the wiring. I wanted it to hold my power…
This is a filler/cover for the unused cutout on the bottom of the XUAV Mini Talon, with a louvered vent added so there's more area for cooling air to exit the fuselage. It was put together using the designs from Mochanic and papo2110, so…
Here's a cover for the Jumper T16 module bay, also fits a Taranis, and should fit just about any radio that uses a JR style module. It's printed in two parts and assembled using two M3-8 screws. This way the tabs that clip into the radio…
This is a pan/tilt mechanism I made up for the Caddx Turtle V2. Here's a video detailing the assembly and all that good stuff. ;) Parts are all rotated in correct orientation for printing. Print with a 0.4mm extrusion width so the thin…
Parts as used in the T1-S VTOL video here: https://www.youtube.com/watch?v=8to8lb4HOFc
Here's my pan/tilt case for the Caddx Tarsier camera. For full details, check this video here: https://www.youtube.com/watch?v=DabCrgiHrd8 Here's a video with it in use: https://www.youtube.com/watch?v=z25h-cisR8c Print Settings Rafts: No…
This is a simple part made to fit the Runcam Split (I'm using V2 here) into the Dart XL from ZOHD. It fits snugly into the nose like the included foam inserts for different cameras, and the Split mounts into it. There are openings to…
This cradle/mount/holder (or whatever you want to call it... lol) fits in the radio stand that comes with the Dragonlink transmitter. It will hold the V2 or large V3 transmitters. Sit the cradle into the radio stand, and the UHF…
Here's the files for the Split Mini pan/tilt I used on the Talon GT in this video: Category: R/C Vehicles
I made this to hold the "Strobon" strobe light from Flytron, which you can find here: http://www.flytron.com/led-light-systems/99-strobon-navigation-strobe-light.html It fits in the cutout on top of the Skyhunter's fuselage which I've yet…
Simple cover for fitting a Strix LED strobe light into the GPS bay on the Sonicmodell AR Wing Pro. https://www.readymaderc.com/products/details/strix-strobes-red Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports:…
Here's my mounting plate to fix a CLRacing F4 Air V3 flight controller board into the top bay of the Esky Eagle, also sold as the AeroScout. You'll need to remove the little plywood box in the top bay, then this sits down onto the wood…
These are all currently available results.
