Counting matching models…
Re-mix of original Gridfinity but instead of the height reference of 2ul x 7mm it now references the overall height from base to top making it easier to work out what height box is required, boxes ranging from 25mm (2x7mm) up to 60mm in…
SunluS2 mount for the Prusa MK3s. Same style as previous Sunlu mount Both halves printed in 0.3mm Draft mode with 40% grid infill with 2 perimeters PETG parts required to join too halves 2x M3x16 cap head bolts 2x m3 square nuts…
Sunlu drier mount for MK3s 2 piece with m3 bolts to join together Parts required 2x M3x12mm Socket head cap screws 2x M3 x16mm csk socket head screws 4x M3 square nuts ( as per Prusa parts) Printed in PETG at 0.3mm layer height 20% infill…
Simple version of an AMS riser with simple butterfly locks to hold together and provision for Led strip lights Material ABS at 0.3 layer height, have included Orca slicer build plates and use some tree supports for the under edge and some…
Simple BTT hdmi 7" screen mount that is easily detachable for when you need to move the machine Provision in centre part to route cables requires a few M3x4x4.5 heatserts
Same holder as the Ratrig but made for the 20x20 profile
Simple model of an attachment to mount the QR stickers on the aftermarket build plates, found no easy way to make the QR code stickers stay permanently attached to the build surface. Found this way you can use a little glue stick on the…
Revised version of my original Sunlu S2 mount for the Prusas , freind has just built Ratrig vcore 3 and was looking for same solution for his Ratrig , this will only work if the machine has the Enclosure frame . Required 2 x M5 cap head…
Same as my previous version except the back is more print friendly being mostly 45 degree angles
Revised version of my original Sunlu S1 mount for the Prusas , freind has just built Ratrig vcore 3 and was looking for same solution for his Ratrig , this will only work if the machine has the Enclosure frame . Required 2 x M5 cap head…
Small bezel mount for humidity and temperature sensors requires 1 x M4x10mm button head screw to mount 12 Pieces Mini Hygrometer Thermometer Electronic Digital Humidity Gauge Monitor LCD Display Indoor Humidity Temperature Meter Sensor…
Printed in PETG 0.2mm layer or 0.3mm layer height , 15% infill , 2 screws required to join case around 2.2mm diameter by 11mm long , fan would require M3 x12 button heads to secure
Looking for a solution to covering the voron2.4 that was removable and not intergrated to exisitng frame also i am a fan of the simplicity of the top mount roll and having no bowden tube. This new frame is located by the Binding plates…
Simple Magnetic door latch that uses 8mmx3mm rare earth button magnets Latch has provision for 3 magnets each side but have found just the 2 each side is enough to secure doors. require 4 x m3x3x4.5mm heatserts and suitable M3 button head…
Simple joiner similar to Silka solution to hold bike chains while waxing in the hotpot Cord is fishing trace line around 1.5mm dia with the end folded and crimped with the ferrel. printed at 0.2mm in petg no supports did run outer brim…
Simple camera mount to eliminate the mounting bracket for the TMEZON wifi solar cameras. usb cable stored in back part of the bracket , i did cut and solder the lead to reduce the length as it was too much to deal with (2mtrs) Printed in…
Simple boxes with Label, Non stackable simplified version of the gridfinity concept that is quicker to print PETG , 0.28mm layer and 2 walls to suit the 1.6mm wall thickness , infill 15% for base
Garmin 515 radar mount to suit the Ibera PakRak IB-RA5. made it so it is off to the side of wheel so as to not get all the mud etc , so far has worked well. i have printed in ASA 0.2mm layer and about 35% infill and super strong, would…
These are all currently available results.
