Counting matching models…
Handle for common action cam or GoPro mounts. The standard screw + nut must be added. If printed with not too much infill, it will float. --> ideally for diving / swimming Attention: Floating function probably just for GoPro clones. (see…
This is a dosing cup for laundry detergent (e.g. for powder or liquid) that I created. Common dosing amounts are marked within the print. It is also helpful for scratching out the last rests from a big powder box. Please consider a small…
This is a casing for an OpenDTU / AhojDTU made from 3 parts. This allows you to read the inverter data of your Hoymiles inverter e.g. for a balcony solar panel. For ordering the right electronic components see pictures. I ordered…
I was not satisfied with the already available lens-protectors so I made another one. This one is very slim and does not influence the general look of the sight too much. Meant for the cheap EOTech clones from China (e.g. for Airsoft). I…
Modelled these to fit on the cheap chronograph that you can get on Aliexpress (see screenshot). They are replacing the standard plates. I used new M2,5x5mm screws but I think you can also use the original screws with some minor adaptions.…
This is a holder / organizer for up to 12 chopsticks + 6 table stands. It has holes for screw mounting but can be also glued. Please consider a small contribution to my Paypal. It would be well appreciated :) Paypal.me/KorbiMuster…
This is a case for a Nixie-Tube-Clock that I created. The Tubes can be bought e.g. on Ebay. The PCB board aswell or alternatively on Aliexpress. The case is supplied with a opening for the USB-cable. Additionally holes for the control of…
This is a drain strainer I designed specifically with the goal to not immediately plug when it gets filled with hair. Fits to common EU-drain sizes. After the version V1 did work, but got clogged quite regularly, I created the V2 which…
This is a tooth brush holder for the "Lächen" electric toothbrushes from e.g. Amazon that I created. The corresponding wireless charging stands are to be fitted in the bottom. The rectangular holes in the rear are for pulling through the…
This one of my older designs where I used four 12gauge shotgun shells for holding pens. The shells are inserted in the top pice ("Shellholder") and this then slides into the baseplate. Please consider a small contribution to my Paypal. It…
Holder for a remote of a LED ceiling light. Fixed with 2 screws. I made it for the OTREN LED lamp (Amazon) that I bought, but I think it will fit also for other similar lamps. Please consider a small contribution to my Paypal. It would be…
This is an easily removable cap for the typical Type F electric plugs (e.g. used in Germany) that I created. I added these on the electric outlets at the head-end of my bed-project for safety reasons. The holes in the front are for…
Because my Picatinny rail was too short and the standard off-the-shelf Lens-Protectors did not fit, I designed this shorter version. (mounted on a Tavor T21) The lens is taken over from the normal lens protectors that can bought e.g. on…
This is a holder for the common HEAT trivets from Ikea (size 7"). The holder is made for storing 3 trivets in total but can also hold just one or two. It is mounted by two wood screws. Please consider a small contribution to my Paypal. It…
I got annoyed by that the hooks of the IKEA Hultarp kitchen organizing rail (see Ikea Screenshot) all the time fell out of the rail when taking off some things for cooking. Therefore I printed these little locking parts. They lock into…
This is a holder for common soap bars Please consider a small contribution to my Paypal. It would be well appreciated :) Paypal.me/KorbiMuster
I couldnt find it online, so I created it by myself. The distance for your hand is 100mm. The screw holes have a diamter of 4mm and a 45° chamfer with 9mm max. diameter. If you enjoy this design and it gives you benefit in your life,…
This is a simple holder for a roll-on antitranspirant (e.g. from Nivea). The holder allows to put the deodorant upside down to use the last drops when the container gets empty. Please consider a small contribution to my Paypal. It would…
A simple holder that can be mounted on the side of a standard Kallax shelf from IKEA. I use it for storing a backpack, so that it doesnt lay anymore on the floor. Fixed with 4 screws, use a small drill for predrilling the holes. If you…
This is a holder for a typical LED-strip remote control that I created. It is made for remote controls with size 124x56x8mm. It is fixed to a surface via two screws (cone head) or glued with a double-sided tape. Please consider a small…
I put my Samsung television onto a rolling board. To avoid, that the television falls down, I fixed the stand with these printed parts. Mounted each with 2 screws. Can be printed without support structure. Probably also fits for other…
This is a mounting bracket that allows the use of a drag chain for the extruder head cables of the Anycubic i3 Mega. It mounts to the old bowden extruder plate, which I dont need anymore because of my HGT direct extruder update. If you…
A simple Trivet / Coaster / Untersetzer for the soap dispensers that have the style of a preserving glass jar. (see Amazon Screenshot) The jars came with a flat blue silicone mat, which was flimsy, ugly and didnt fix the jar on its place.…
Buffer block that, when printed in TPU (e.g. 15% infill), gives more flexibility to the part and therefore is less rough on the frame of the GBB. Further the recoil spring is not interacting anymore with the black plastic fins (which are…
This reservoir for Airsoft BBs is shaped like the typical M4/M16/STANAG magazines and can fit into normal mag-pouches. I use it for refilling my Hicap magazine on the field. Consits out of two parts --> main housing and lid I recommend to…
This adapter allows feeding the GBB magazine of the VFC FAL / OSW with a High-Cap magazine. I used a "Dboys SCAR-H Mk17 500rds Magazine". There is quite a lot of filing and dremmeling needed. Therefore I only recommend it for experienced…
Next to my bed I dont have space for a nightstand so I designed this glassholder for urgent water needs in the night. :D It is meant for rather big glasses (e.g. 0,5l beer glass). It is mounted with 3 screws which are hidden on the bottom…
These are all currently available results.
