P
Printablesstratoprinter
Fluval Flex 9 Gallon Sliding Feeder Cover
Fluval Flex 9 Gallon Sliding Feeder Cover. PETG, 10% infill. Glue on the slide retainer
- Downloads
- 217
- Likes
- 16
- Rating
- 0
All models
Counting matching models…
P
Printablesstratoprinter
RC Plane Servo & Horn Protector
Servo & Horn protector for my 3Dlabprint Lightweight Series planes or any plane that uses 9g servos. I used ABS but any material can be used. I printed flat with supports and used a very small amount of glue in case I needed access to…
- Downloads
- 155
- Likes
- 27
- Rating
- 0
P
Printablesstratoprinter
QX-Motor 30mm EDF Intake & Exhaust Duct for FMS Alpha Jet
Designed this around the QX-Motor 30mm EDF 7000KV For the FMS Alpha Free Flight Airplane https://www.horizonhobby.com/product/free-flight-alpha-red-kit-467mm/FMM073RED.html . Intake area is slightly more than EDF. Exhaust area is about…
- Downloads
- 148
- Likes
- 15
- Rating
- 0
P
Printablesstratoprinter
Fluval Flex 9 Gallon Feeder Cover
Fluval Flex 9 Gallon Feeder Cover. I used PETG, 5% infill, Plate supports. Can make with whatever parameters you want.
- Downloads
- 140
- Likes
- 9
- Rating
- 5
P
Printablesstratoprinter
QX-Motor 50mm EDF Mount for Wing Wing Z-84 flying wing.
0.2-.3mm, 5% infill, PETG, but you can use whatever filament you would like. Fit like a glove. Glued to foam with foam safe CA. Slight friction fit on front of EDF. Used a small amount of glue to install EDF. It is stout so can probably…
- Downloads
- 118
- Likes
- 4
- Rating
- 0
P
Printablesstratoprinter
3536 Brushless Motor Mount
I designed these two 3536 brushless motor mounts specifically for an old Cessna 337 Skymaster ARF kit I never got around to finishing. This model was from Nitro Models which does not seem to sell airplanes anymore. I finally dusted it off…
- Downloads
- 91
- Likes
- 2
- Rating
- 0
P
Printablesstratoprinter
Coral Plug Holder 1 & 2 inch
Coral Plug Holder 1.25 & 2.25 inch stem PETG 0.24 mm layers 100% infill with 4 walls O.415 in I.D. for a 0.40 in plug
- Downloads
- 73
- Likes
- 5
- Rating
- 0
P
Printablesstratoprinter
Hyperflow 56mm EDF Thrust Duct & Mount
IDesigned this for the Hyperflow 56mm EDF. Used recommended exhaust area for efficient thrust amount. I used two layers @0.3mm and 5% infill. Can be printed with whatever you would like.
- Downloads
- 43
- Likes
- 7
- Rating
- 0
P
Printablesstratoprinter
Floating Plant Guard 10 Gallon Tanks
Floating plant guard for 10 gallon tanks. This one was an aqueon. I used two suction cups with 0.25 in holes in stem. 4inx12in For suction cups with 0.25 in holes Included .step file for any desired adjustments PETG 3 Walls No infill Brim…
- Downloads
- 41
- Likes
- 2
- Rating
- 0
P
Printablesstratoprinter
Spektrum Replacement DX6i Roller Menu Scroll Button
Spektrum Replacement Roller Menu Scroll Button with metal hex shaft for roller sensor. For DX6i, DX7S, DX8, DX9 transmitters. 0.12 mm layer 15-30 mm/s PETG 1.6 mm hex wrench Insert hex wrench into button side and protrude appropriate…
- Downloads
- 38
- Likes
- 2
- Rating
- 5
P
Printablesstratoprinter
Wavy Floating Plant Guard Fluval Spec
Floating plant guard Fluval Spec Fish Tank for suction cups. Spans width of tank to keep plants from filter intake and outlet. PETG 3 walls .2 mm no infill
- Downloads
- 37
- Likes
- 6
- Rating
- 0
P
Printablesstratoprinter
RC Remote Control Wall Mount
RC remote control wall mounts for airplane/helicopter/multi-rotor remote controls with wire handle. Two models one just for adhesive mounting and one for screw mounting. I also included an extended flat version for flat plastic handles.…
- Downloads
- 34
- Likes
- 2
- Rating
- 0
P
Printablesstratoprinter
Small Propulsion Pod for 2206 Brushless Motor
Small Propulsion Pod for 2206 Brushless Motor for Hand Chuck or Single motor to Twin Conversion. For Flat bottom airfoils. Includes cowl. Has ventilation. I designed this specifically to fit and convert my CG-4A Waco glider from…
- Downloads
- 33
- Likes
- 8
- Rating
- 0
P
Printablesstratoprinter
E-Flite BL50 Motor & ESC Mount
E-Flite BL50 motor & ESC mount with ventilation and air scoop with cowling. Specifically designed for my highly modified Sig Kadet Senior electric conversion. Could be used on other planes that it fits onto firewall. V1, V2, V3 uploaded.…
- Downloads
- 32
- Likes
- 1
- Rating
- 0
P
Printablesstratoprinter
Re-mix, Printable Rotor Blades for Giroprint2020 autogyro
I was not satisfied with the stiffness or size of the rotor blades for the giro2020 3D printed autogyro found here https://www.thingiverse.com/thing:4172759 . So I went searching for some off the shelf and other printed solutions. I found…
- Downloads
- 23
- Likes
- 3
- Rating
- 0
P
Printablesstratoprinter
Eheim Jager 50W Aquarium Heater Water Jug Adjustable Mount.
I get pre-conditioned 5 gallon water jugs refilled at our local Fish store for water changes and needed to heat before changes so as not to be to cold. I had this heater laying around so I decided to create an adjustable jug mount since…
- Downloads
- 18
- Likes
- 2
- Rating
- 0
These are all currently available results.