P
PrintablesTomik
Spray can holder for Multiboard
My version of spray can holder for Multiboard. 15% infill, 0,25mm layer and 2 walls will be enough even for 450ml WD-40
- Downloads
- 99
- Likes
- 15
- Rating
- 0
All models
Counting matching models…
P
PrintablesTomik
Multiboard Battery Holder
Battery (AA and AAA) holder for Multiboard using the basic mounting.
- Downloads
- 85
- Likes
- 10
- Rating
- 0
P
PrintablesTomik
Mason Jar Holder
I used 0.25mm layer, 15% infill and 2 walls for empty jars. If you want to use them for full jars make the walls 3 and increase the infill. There are 2 models for each side - front and rear.
- Downloads
- 72
- Likes
- 45
- Rating
- 0
P
PrintablesTomik
Filament shelf - Filament Regal 24mm holes
I had a few broom rods laying around but they were 24mm in diameter so I adjusted holes and they are 24mm now. It is a tight fit so it won't fall off. But always check your print tolerances.
- Downloads
- 68
- Likes
- 9
- Rating
- 5
P
PrintablesTomik
Collection of Glue Holders for Multiboard
31, 36 and 47mm diameter for any circular object
- Downloads
- 50
- Likes
- 4
- Rating
- 0
P
PrintablesTomik
PS4 controller desk mount
I liked the @BokuNoMaxi's design so I remixed it to be able to mount my PS4 controller on a desk. It can be tightened with a screw that is included. The desk thickness can be max 20mm. Print the mount as is, no supports. I printed it with…
- Downloads
- 33
- Likes
- 5
- Rating
- 0
P
PrintablesTomik
Rotating Spice Rack
This is my version of Spongybob1958's Spice Rack Pullout https://www.thingiverse.com/thing:4356449 . I designed this for bags of spices as you can see in the pictures, it also can store any other bags fit similar ingredients. This version…
- Downloads
- 32
- Likes
- 15
- Rating
- 0
P
PrintablesTomik
Monitor Stand
This monitor stand is printed in 2 pieces. Each of them has a locking mechanism that holds them together. It's quit a tight fit to ensure stability, so be cautious when locking them together. I recommend to print them upside-down, that's…
- Downloads
- 30
- Likes
- 1
- Rating
- 0
P
PrintablesTomik
LED strip holder for E3V3SE
It was a bummer for me to see how is the print doing even with led strips on the edges of my box for the printer. So I came up with this. It just hooks on the X axis motor. I recommend to print it in PETG because of the heat, PLA will…
- Downloads
- 19
- Likes
- 2
- Rating
- 0
P
PrintablesTomik
Power Brick Holder
I take my laptop to work/school everyday so I wanted something to hold the power brick when I'm at home but something simple enough so I don't have to much work of removing it when I need it. I printed it with 20% infill, 3 walls and…
- Downloads
- 13
- Likes
- 2
- Rating
- 0
P
PrintablesTomik
Organizer for small Parkside electric screwdriver + gola set
Print every piece on the bottom side. I printed it with 0,25 layer and 10% rectangular infill. Feel free to remix it or use it as base for yours
- Downloads
- 9
- Likes
- 1
- Rating
- 0
P
PrintablesTomik
Door hinges extended
When I installed new doors in my old kitchen cabinet I realised that the screws came directly between the frame and support wood I added earlier. So I came up with this simple thing that spread out pressure that is on the screws. I…
- Downloads
- 8
- Likes
- 0
- Rating
- 0
P
PrintablesTomik
EN3V3 Tools Holder
I was tired o having them in the zip lock back in my drawer so I made this for a multiboard. I printed it with 0.25mm layer, 15% infill and 3 walls
- Downloads
- 5
- Likes
- 0
- Rating
- 0
P
PrintablesTomik
Monitor stand
I made this monitor stand because I did not have enough space on my desk so my monitor had to go somewhere else. It depends on the weight of the monitor but I used 20% infill with 3 walls and 0,25 layer height and it's pretty tough that…
- Downloads
- 5
- Likes
- 0
- Rating
- 0
These are all currently available results.