Counting matching models…
In printing the light saber ( https://www.printables.com/pl/model/350959-collapsing-sith-lightsaber-color-removable-blade ) at 50% I found it looked like a wand so I created a couple wand housings for it. I print the light saber blades…
When working though y-axis layer shift issues I designed this model to excite my particular failure mode (basically circular shapes seemed more likely cause my printer to fail). Probably won't be effective in all failure scenarios, 'but…
The Door Handle Door Lock Rod Clip on my 1998 Honda Accord, this clip does the job as a replacement part. Tested on the front doors only so far, right and left doors need a mirror version but I've found the non-mirrored version also…
A redesigned sepal for https://www.thingiverse.com/thing:673762 . This prints without supports and is smaller and tighter to the flower but a little less fancy as the one on the original model. Pictured filament is Makergeeks translucent…
I needed a Bow Sander to help smooth out the slot of one of my prints. I came up with this guy to do to trick. Takes a ~12mm wide strip of sand paper and stretches it across the curved bow. Ends are held in place by removable, snap-in…
Costume dagger with holes to press fit 5mmx2mm magnets. With magnets in place you can combine 2 to make one for a fun play factor. Print instructions Category: Toys & Games
Wearing masks all day at work was making my ears ache. I came up with a print-in-place chain to hook in the back to keep the straps from resting on my ears. Adding a revised version of the larger chain with improved clearances for earier…
Minimized base for digital sundial. Print instructions Category: Sculptures
I love Frenshape's Dodecathing and wanted to add a little extra flare to the spans. I also filled in the endcaps so I could scale down the prints if desired. I've been able to print successfully at 60% with the new endcaps but I've not…
I found the MMU3 buttons a little hard to push and the existing solutions were too loose in the button holes and ended up partially turned so I made my own extensions. Delete the "_Let" parts if you'd prefer a debossed button. I've found…
My Daughter asked for a toy camera to play with her LPS toys and I whipped this up. Uses 3mm filament for the legs, should print without supports. Print instructions Category: Toys & Games
A 3 Part dice carried that screws together to protect your dice. Each Part designed to be printed in 100% vase mode, 0.7mm walls. I've also handed edited some gcode files to enable MMU prints of the screw-on cap for some fun effects.
I decided I wanted to beef up the emitter assembly of the propmaker lightsaber - and by the time I got that far in porting their design in to my own Fusion 360 project it seemed like it would be fun to continue to tinker with it and make…
SquidGame Mask cut in half for easy printing. Added eye inserts to be printed with grid infill and 0 top/btm lyrs. I used super glue to attach the two parts and then used a 3d pen on the inside to weld the seams for additional strength.
Seemed like the floppy Dragonfly needed a stand Print instructions Category: Toys & Games
I found that the One Ring muffled the sounds out of my Dot so I made a quick acoustic mount for the Dot + Ring. Print instructions Category: Sculptures
I wanted to put an E3D knockoff on my Tevo tarantula so I designed an X-Carriage and cooling solution to accommodate it. Required HW: 10 M3 Square Nuts 1 M3 Hex Nut 7 M3x10 Screws (I used hex-head Caps) 2 M3X25 Screws 2 M3X30 Screws The…
Just adding tree supports to the foot since my printer can't print such a large thing balanced on a pin point. Print instructions Category: Sculptures Overview and Background Blah why is this section required? Lesson Plan and Activity…
Proto-pasta spools are made of corrugated cardboard which tends to be soft and sometimes gets damaged. A couple of my protopasta spools are damaged in their central hole and I wanted to make a vase mode print to strengthen them. Designed…
For some reason some of my filament seems to roll over in the MMU2 spool holders to form an overlapped loop on unloading. When the MMU2 pulls the filament back in for the next load the loop rolls over on itself and can snap or form a…
I designed this to replace the plate in the arm rest of my 2000 Chevy Impala used to connect the hinge of the arm rest to the base of the center console. The original plate is designed ridiculously thin for the application and eventually…
Just a quick stand for the Adafruit Sand Physics Toy. It snaps together without glue Print instructions Category: Physics & Astronomy Print Settings Printer: Tevo Tarantula Rafts: No Supports: No Resolution: .3 Infill: 15% Post-Printing…
I was worried the Vorpal Bot would skid too much on my smooth floors so I made some little booties out of TPE. Still building the bot so all I can say right now is that they fit nicely on the feet. Even If they don't help with skidding…
This a clip for an Omnipod PDM with a silicone case installed. My daughter got a new case for her PDM that had a Velcro mount for the PDM but still wanted to use the silicone case for PDM ruggedization so I came up with a clip she could…
My current attempt at a Chimera Version of the peanut fan duct. Should print with the same settings as the original. I've only printed the bottom section so far but I didn't alter the top section any so it should be fine. Print…
Another new filament clip design. Works like similar friction clips except one of the paths is also curved to place the filament in tension too. Small / fast print and seems be working well.
120mm fan mount for the tevo tarantula ramps "enclosure". Nothing special required to print. Print instructions Category: 3D Printer Parts
A little enclosure for a Wang DD 22 mosfet, really designed for screwing to a base like mdf. Shield and carrier should print without supports as oriented. Shroud may need internal supports for the overhang though my friend has printed it…
These are all currently available results.
