Counting matching models…
Don't waste your precious time and filament printing a so called “calibration cube”! This quick print provides clues for all the important features and settings: Extrusion width E-steps / rotation distance (X, Y, Z) Bridging Cooling…
I designed the cap to match the dimensions of the originally used milk bottle cap: https://www.printables.com/de/model/350262-gridfinity-1x1-bottle-vase-mode 3 versions of the cap are available: Gridfinity label Gridfinity logo Gridfinity…
Two variants available PLA works, but PETG may be better (?)
You can adjust the phone stand in 3 positions by tilting the arm until it latches Feel free to give feedback as I'm shure this little thing can be improved :) Printing Standard print settings for your printer Print the parts laying on the…
This simple stand lets you put your Sonicare toothbrush somewhere to dry and not fall over ;)
You can store up to four 18650 batterie cells inside this minimalist battery container. The lid is held in place by friction - no fancy closing mechanism required. Print Settings Spiral/Vase mode 0.2 mm layer height 5 bottom layers 1 mm…
A nice little encoder knob 2 Versions: D shaft - 6 mm diameter, 10 mm deep Round shaft - 6mm diameter, 8 mm deep (fits ender 3)
The original seal for my IKEA Atlant kitchen sink plug broke - it wouldn't stay open any more due to the corners of the little standoffs being rubbed off by years of usage. As there where only a few clunky 3d models available online i…
I tried a lot of fans and fan mounts for part cooling for the BIQU H2 on my Ender 3 - nothing worked really So i designed this 4010 radial fan mount. It is simple and works. i also designed a fan shroud fitting this setup. Note on BIQU H2…
Printing 0.2 mm layer hight 2 walls/perimeters no infill required
The cap i designed the bottle for is from the german Aldi-Nord and has about those dimensions: 36 mm minor diameter 7 mm lead 3.5 mm pitch The cap from my Gridfinity bottle also fits:…
Protect your precious Nikon batteries with this simple and “snappy” case! Printing Use the standard print settings in your favourite slicer. Make shure that “Minimum travel after retraction” (Prusa-Slicer) is set to 1 or lower I used eSun…
Printing Material: TPU Perimeters/Walls: 5 Installation Push the part into the frame before inserting the slat Dimensions The Part is designed to fit 70 x 12 mm slats
Dimensions Width: 36 mm Height: 25 mm Mounting Hole Diameter: 3.7 mm (fits M4 screws) Depth: 20 mm Printing PLA/PLA+ works very well. This model should be printable without any support or brim. Four or more perimeters/walls may be needed…
Do you have your roll of garbage bags floating around somewhere inside the kitchen cabinet underneath the sink? Print this garbage bag dispenser and install it using the holes (5 mm) and screws of the kitchen cabinet! Printing no supports…
The original organizer for the Proxxon screwdrivers was intended to be wall-mounted - not what i wanted. So I designed this stand which can be carried around and placed next to the current project. Printing Infill: 15% Perimeters: 3…
A simple solution to a simple problem. Printing 3 Perimeters / Walls 0.3 mm layer hight Material: PLA, PETG, … whatever you like :)
A quick 5 minute print that lets you hang up dish towels without loops
Simple container that looks like a button. Print Settings 0.2 mm layer height works pretty good no support no infill
Minimalist container for three 18650 cells - friction fit Printing Vase mode 1 mm extrusion width (yes, this works with a 0.4 mm nozzle) 0.3 mm layer height 3 bottom layers If the lid/cap fits too loosely try scaling it down in your…
Tool for presta valve core replacement
Dimensions Hole spacing: 128 mm Holes: 4 x 18 mm Materials PETG or ABS for durability - PLA+ may also work Post printing You may want to clean up the bottom with sandpaper - it shouldn't be visible anyway Update 2022-12-15: V2.3 - some…
Print Settings no infill no support material Materials: PLA, PETG, TPU, ABS, … ≤ 0,2 mm layer height 3 or more perimeters “ensure wall thickness” Version 2 should be printed in Vase Mode: 1 mm extrusion width 0.2 mm layer height 5 bottom…
One day I noticed the Y-belt on my Ender 3 not beeing parallel with the Y-axis extrusion and sometimes rubbing. After some research a came up with this solution. just push in the original f688 bearings and you are done!
Drain strainer for 40 mm drains Printing Supports from the buildplate
Printing Vase Mode 0.2 mm layer height 5 bottom layers 1 mm perimeter/wall thickness Materials: PLA, TPU, ABS, …
The stand is available in sizes to fit tanks with up to 28 mm in diameter. The 510 connector fits loosley. Print Settings 3 or more perimeters “ensure wall thickness” ~ 0,2 mm layer height Material: PLA, PETG, TPU, ABS, … Update…
Print one clip for every party guest in a different color I prepared versions for the 3 common diameters of drinking straws: 6, 8 and 10 mm If you need a different size, just use the 10 mm one and scale it in your slicer Printing print it…
Equip your Raspberry Pi HQ camera lens with a privacy lens cover! The lens cover should work with any lens with 40 mm outer diameter. What you need Printed lens cover ring Printed lens cover flap 16 mm of 1.75 mm filament Printing…
Dimesions The wall hanger should fit all spirit levels with a ~10 mm hole 27 mm long hole size 5 mm OD 9.5 mm Printing Standard print settings with a 0.4 mm nozzle is all you need
I designed this mount for the Waveshare camera "RPi Camera (B)" https://www.waveshare.com/rpi-camera-b.htm Feel free to adapt the mount for any other Raspberry Pi camera - STEP file included :) Printing 0.2 mm layer hight no infill required
What you need Apart from the 3d printed parts you reuse some parts of the stock caster / castor wheel Original Parts axle: ~ 30 x 5 mm 2 wheels: 35 x 7,5 mm pin: 6 mm diameter top, 7 mm diameter bottom Printed Parts caster body 2 washers…
These are all currently available results.
