Counting matching models…
This is a CNC spoilboard I coded after looking at a few designs around the web. I wrote it for my SainSmart CNC 3018 ProVER with the Y extension (3040). If you have this machine, this may work for you, but check that the measurements are…
Designed in OpenSCAD for the laser linked below: https://www.sainsmart.com/collections/laser-cutting/products/genmitsu-cnc-blue-violet-light-fixed-focus-laser-module-kit-for-3018-prover-3018-mx3 Air hose connector designed for the…
This is a very small and fast print. The source is included if you need to change a tolerance. The Nitehawk fan board is nearly identical to the regular HartK Stealthburner fan board save for the gender change of the header pins from male…
Background I have a CNC 3018 variant by Sainsmart called the ProVER. It does not have a lot of vertical clearance, so I wanted something with a small footprint. I did this in OpenSCAD, so you can change a few things if you need to. I…
Remixed the original holder in Fusion 360, adding magnet holes. Plug remixed in OpenSCAD, wire slot width was reduced.
— This is a work in progress and some things may change — Parametric Power Supply Cover with Switch Unnecessary Background Information I recently purchased the 300 watt spindle upgrade for my Sainsmart 3018 PROVer CNC router. I wanted a…
Ender 3v2 X and Y mounts for adxl345 for Klipper Resonance Tuning This print was inspired by https://www.thingiverse.com/thing:4882714 These are low-profile mounts that clip on the X gantry and the printer bed + surface. They are a…
Changes September 27, 2021 v17 of Left Bottom -- this model fits the space much better. The wire slot was enlarged. The crosses that fit in the frame screw holes were slightly enlarged for a tighter fit. The right hand rails were…
I am very impressed by the original project. I like working with OpenSCAD very much. As a half-decent programmer, I appreciate all the hard work that led to this print. Because the code was well-written, it was much easier for me to…
See original model for details: https://www.thingiverse.com/thing:4928394
Background This is my first attempt at using a cable chain, and also my first experience with using Onshape. Usually I use OpenSCAD but I was uncertain I could measure and model the wire cutouts on the back of the DDX with my current…
When switching between the Recreator and the MELD machine, the four screws holding the mounted motherboard to the 2020 rails must be removed and then reattached to the alternate machine top. These thumb screws make it a little bit easier…
I finally jumped on the bandwagon and put my printer in chains. A few of johnniewhiskey's links were too skinny for my setup as I have a few JST-SM connectors. So I needed to loosen my belt. Ha ha ha. I tried Chilbet's model and it is a…
Only support the overhanging areas. Do not support the filament hole. I used painted on supports in PrusaSlicer. Changes: October 15, 2023: Added brace to support frame per @AbelPaz_1246682. It should help with stability. October 16,…
I've just begun to brew beer and I don't have any proper bottles yet. My first beer was a Porter and looked just about the same as Diet Coke. I didn't want people mistaking my beer for soda and then dumping it. Slap one of these bad boys…
I had issues printing the “tube” model from the original design. The supports were very hard for me to remove without damage. I had some old PVC pipes lying around, so I chopped them up instead and made some simple fittings. The fittings…
I got a Linksys e8450 router a few weeks ago and the first thing I noticed was the brightness of all the blinking LEDs. I wanted a way to lower the intensity as I'm in the room at night and it can be a bit distracting. So the idea here is…
This is a remix of https://www.thingiverse.com/thing:3973801 Background: I wanted to give this a smaller profile than the original thing. I removed two walls from the square top to make it easier to slip under the router bit. I think it…
These are all currently available results.
