Counting matching models…
If you like the bambu hotend, but you have a groove mount, this is for you. Added V2 with improved clearances, and mirrored to have the heads of the mounting screws on the short fin side of the hotend.
Lightweight mounting for Phaetus hotend (and clones) with sherpa mini, orbiter 1.5 or 2.0 extruders. Integrated 5015 blower parts cooling duct, 40mm heatsink fan duct, and BLtouch mount. Edit 16/05/22: Added dragon volcano version Edit…
With this it is possible to clearance your side seals with even a cheap rotary tool from Lidl! The threaded collar must be glued into the tool with superglue. 22/03/2026: Added model with larger tool hole size by request
This simple jig can be used to quickly assess the wear and flatness of apex seals for all Mazda 13B engines. It is also useful for attaching the corner pieces prior to assembly.
This adapter allows easy installation of any bolt on type feet or vibration dampers. Known compatibility with X-max and X-plus, but may also fit many other Qidi printers. Designed for M4 fittings, recommended feet are squash ball cup…
An updated version of my direct drive mounts for the Tronxy Gemini S IDEX 3D printer. This new version has an improved heatsink duct and uses 5015 blowers for part cooling, Phaetus Dragon hotends (and it's clones), along with Orbiter v2.0…
This is a full kinematics overhaul for the Tronxy X5S and X5SA series printers. I have tested all these parts together, and have had clean prints at up to 120mm/s with PETG. It requires 3 mgn12 linear rails, the length of which will…
Simple brackets to allow use of dragon hotends with Tronxy Gemini S printers. Should also fit other hotends with similar 4 screw mounts. Low versions mount the hotend slightly higher, bringing the printhead lower to the bed.
The original bushes wear out and make an annoying noise. Sourcing replacements can be difficult so I made this. Recommend printing in Nylon or other high temperature, low friction material. If printing in hard material, advise splitting…
With this it is possible to clearance your side seals with even a cheap rotary tool from Lidl! The threaded collar must be glued into the tool with superglue.
Improved heatsink duct and part cooling duct, part cooling fan now uses a heat-set thread insert for mounting. also included is a trimmed X endstop mount to clear the part cooling fan.
A pair of X carriage mounts to suit the Tronxy Gemini S IDEX printer using Phaetus dragon hotends (or clones) and Orbiter 1.5 extruders. cartridge type thermistors are required for proper operation, and the esteps will need to be adjusted…
As the summary says, just a bracket to hold the sonic pad sensor on an EVA 3 carriage. I have the EVA 3 on my Ender 5 plus, along with the sonic pad and was just using the BLtouch screw to hold it for measuring but I realised I should…
This direct drive mount attaches to the stock X carriage of the Adimlab Gantry-S (may also fit other Adimlab printers) and allows the use of either Phaetus dragon or Slice engineering Mosquito hotends with either Sherpa mini, Orbiter 1.5,…
Remixed rear plates to allow the use of kevinakasam's ender 3 belt driven Z conversion with Adimlabs Gantry-s (and possibly Gantry pro) printers. As my printer is running a direct drive setup, I didn't include an extruder mount on either…
A slight revision of a simple carriage I made back in 2020 to improve a PxMalion T320 I got from Amazon for £100. I have integrated the 2-in-1 fan duct by Epionezero on Thingiverse found here; https://www.thingiverse.com/thing:839620…
Updated version with improved heatsink duct and part cooling duct. Part cooling mount now also uses heat-set thread insert rather than a free nut.
These are all currently available results.
