Counting matching models…
Minimalist version of the original vertical mount . I've thinned the walls and clip to remove material to reduce the filament used and speed up the print time. My Shelly 2.5 will not be visible, so did not need the fillets and Shelly logo…
Enlarged Raspberry Pi Zero W case to accommodate a Waveshare Ethernet/USB hub hat on top. Remixed from: https://www.thingiverse.com/thing:1165227 A lot of adjustments from the original model as the port alignment was not good and the case…
I want to print higher temperature materials, minimise warping, failed prints and contain the gases released by those materials. This is my build log to enclose my modified Creality Ender 3. One motivation for this project is to gain…
Noctua NF-A9-14 90mm fan cover for Meanwell PSU. Although intermittent, the stock fan on the Meanwell LRS 350W is loud when running. Switching it out for a 90mm noctua fan significantly reduced the fan noise. I've reduced the hex mesh…
Revised: v2 files simplify design, specifically the pegs and how they insert into the back plate. Print all parts. I used PLA but most other filaments should work fine (PETG / ABS / ASA). Assembly Insert pegs through back plate holes.…
Sherpa mini mount to fit the original Ender 3. 2021-12-09: Uploaded new STLs (v3), in the version from Nov 8th I mirrored the model upside down to minimise supports when I should have rotated it 180 degrees. 2021-11-08: Supports added to…
Mount an IEC C14 (kettle lead) in-let switch to 2020 extrusion. This model can be useful if you've moved your PSU outside an enclosure. See my companion model to mount a Meanwell LRS power supply on 2020 aluminium extrusion. Hardware 2 x…
35mm DIN mount for this 20A 300W buck converter that I use for 12v fans and LED strip. The mount should be seated on a Voron DIN clip (also available in this thing ). I've included two mounts, one that orients the bucker converter along…
This is remixed from the Voron 2.4 repository, using the bracket for the SKR E3 Mini v2 . This remix adds an additional arm to support the screw terminals on the E3 Turbo. There is no screw hole at that position on the board for the arm.…
Corner bracket (35mm x 35mm) for V slot aluminium extrusion. Helps improve rigidity of extrusion frames. Includes cable channel and anchor for a cable tie. Holes are 3.5mm diameter with slight countersink for M3 screws + T nuts to attach…
Separates the IKEA Skadis container pot into smaller sections so smaller items do not mix / fall over. Prints best with supports, upside down with the top touching the build surface.
Mount for a Meanwell LRS power supply to 2020 extrusion. Designed to mount to a corner but could be attached elsewhere using fewer bolts & T-nuts. Model uses M4x5mm bolts throughout, 4 to attach PSU to housing, 4 to attach housing to…
Mounts to 4040 extrusion using M4 bolts and T nuts. I used countersunk bolts for a flush finish. Print in PETG / ABS / ASA or any high(er) temperature filament. Built and available on OnShape if you need to make adjustments.
Mount [and optionally charge] your A Series Pixel Buds on your Skadis peg board. I recommend orienting the parts for printing as shown in the images. The hook model does not require supports, only the cup. Slide the cup into the hook and…
Helps align drilling out the end of 2020 extrusion to increase the bore hole. The tolerances on the insert and the extrusion are snug, so please calibrate your filament flow rate. The inserts allow you to change the drill size, 4mm, 5mm…
These are all currently available results.
