Counting matching models…
This is a remix of a TPU stick saver that I found here: https://www.printables.com/model/254267-steam-deck-stick-protector I found that it was much easier to take the stick saver off if there was a little tab so I added one into the…
I wanted some larger key/numberplates because the originals that these were based on were a bit difficult to get a grip on. Source Fusion 360 file included. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No…
I couldn't find a charging display stand for an iPod classic so I figured I'd just make it myself. Fits an iPod classic with the "stubby" charging connector. It's not perfect but gets the job done and looks good IMO. Print Settings…
I designed this because I wanted some extra charging bases for my Sonos Move but they're about $70 each for new ones. Knowing the charging base isn't anything more than an 18VDC power supply, pogo pins, and the base I wasn't going to drop…
This is a replacement coffee scraper for my Jura S9 (original part looks like this: https://www.jura-parts.com/Jura-Brew-Group-Coffee-Scraper-Blade-V3-p/10051.htm ). The original one broke but I was able to measure it for dimensions and…
I found that I needed another couple charging bases for my Casper Glow lights but I couldn't find them online (and figured they'd be expensive if I did) so I designed my own. Each base will need 2 small pogo pins like these…
A New V2 based on this design can be found here: This is a custom head design for a walksnail Moonlight VTX for the SpeedyBee Master 3X quad. It should also be compatible with the Bee25 however I haven't tested it. The antenna mount is…
This is a remix of a great stand for the steam deck. If you don't have the case listed below please consider printing the original of this dock. NOTE: This remix is to allow allow the steam deck to still fit on the dock while in the JSAUX…
I made this to fully protect my solar battery terminals from any possibility of shorting out. I print them in red and black for color coding the terminals and once I have my wiring in place I stick them down using VHB type double sided…
I made this small mast after finding that hard-mounting my GPS to the frame using this design ( https://www.thingiverse.com/thing:4057458 ) put it too close to the EMF of the controller/motors and threw off compass readings so iNav…
This is a tilting enclosure for the Seeed Studio MMWave Lite radar module (https://wiki.seeedstudio.com/Radar_MR24HPC1/) with a base that can hold a microcontroller like an ESP8266 D1 Mini. Printing Notes: This is designed to be printed…
I designed this to replace the original puck in my delta bandsaw. I printed this in PETG but PLA would probably be fine as well. In the uploaded STL files the slot has been offset by a couple of mm from center so that the blade is…
I designed these little shelves to make it easy to store all of the little parts bins that screws, potentiometers, etc often come in. The self sides should be 3D printed while the shelves themselves can be 3D printed or can be easily…
This is a mount/holder for a TBS crossfire nano rx module for the SpeedyBee Master 3X. It's designed to fit roughly like the original RX cover (slipped under the frame on one side and screwed in on the other). The one pictured is slightly…
The little pins that form the hinge on my original lid broke so I measured the original and designed this to be a drop in replacement. The one installed in the pictures is the new printed version and even stands up on it's own when opened…
This is a servo control mount for the manual rectangular ducts in my house (similar to the ones shown in the pics). They accept a normal servo like the one found here https://www.amazon.com/gp/product/B076CNKQX4 You'll need 4 M3x10mm…
This is a replacement bow retaining clip for standard tabletop Kitchenaid lift mixers. The original one that came with our mixer broke and these appear to be somewhat of a pain to find so I designed this quickly to get my mixer back up…
I bought a second hand NUC 11 (NUC11TNKi5) on ebay but it was missing the bottom plate so I got a great deal. A bit of measuring and a 1hr print later and it looks as good as new! I added some little rubber feet to ensure the bottom gets…
These are TPU feet/arm bumpers for the SpeedyBee Master3X Frame. There are 2 main variants: The "standard" version The "with antenna holder" version (meant for a 900mhz TBS Crossfire or similar antenna) For each of these there are 5…
Print in PETG (possibly PLA but untested) and it should snap-fit onto the center bottom of the Master 3X and block dirt/snow from getting into the electronics from the under-side. You can find the camera dirt guard pictured in white here:…
Made this strain relief for the thunderbolt 2 / mini display port cable for my monitor. After years of use the cable began to fray/break so I figured this would help prolong its life. Before installing it, a little nudge on the cable…
I love my Extreme Q vaporizer for aroma therapy but I found that the form factor was “too big” for me. It easily tips over and takes up a lot of room on my small side table so I completely re-designed it to be shorter and more boxy so…
Designed to fit 9 of the common blue silicone bit holders found in cheap multi-bit kits like the ORIA screwdriver kits (8mm x 40mm blocks). Design includes mounting on the back so that it can be screwed into a desktop shelf unit like…
Where to begin... I needed a durable Caddx Moonlight head unit for my Master 3X. I also happen to use GoPro Hero ND filters because they're just better than the caddx ones so I made the filter adapter found here . The result is this head…
Basic cable clips that use small #6 screws to mount to the baseboard/wall. Can pretty easily be scaled up or down as needed. Can be printed in either PLA or PETG (I mostly use PLA). Category: Organization
Holds the LTT Precision Screwdriver at a nice angle for easy use. Designed to mount on a desk/shelf with a small screw. Print Settings Rafts: No Supports: Yes **Resolution:** 0.2mm Infill: 15% **Filament Material:** PLA Category: Tool…
A simple TPU adapter that lets you use cheaper/easier to find ND filters for a GoPro Hero 11/12/13/etc to a Caddx Moonlight camera. The GoPro Hero filters seem much easier to find and have much less color distortion than the caddx ones.…
The MAKE Controller from MakingThings was foundational to my love of electronics and programming so I made this little display stand to keep on my desk. It integrates a little hidden section at the bottom to put an RGB strip. I programmed…
I made this front extension to move my FPV camera forward (and my VTX can now sit just behind the camera which makes cable management easier). The bottom and top sections get bolted to the frame and they also screw into each other near…
This is a rigid extension for a GPS module cap thats mounted in TPU. The GPS is a M8Q-5883. I originally had only the top section that mounted to the top side of the frame however I had terrible vibrations from the resonance of the…
I kept shredding my battery leads without a good mount for the battery connector so I made this. It's not perfect and does break occasionally but now I have a good rigid pivoting mount for my XT60 battery connector. print in PETG or…
These are all currently available results.
