Counting matching models…
Reverse bowden IR Sensor Cover for the MK3s I have included 3 versions one for the PC4-M10 pass through connector and another for the PC4-M6 connector. I have now added a version for the PC4-M5 connector. Edit 19/2/19: I have added a M5…
This 6 cell module tray for starting your seeds, designed to be strong and sturdy so that i can be reused many times, with a large hole in the base to aid drainage and the easy removal of plug (plant) once the plant is ready for…
UPDATE: There is now a V2 of these cell trays with an improved design please check out https://www.prusaprinters.org/prints/71854-seedmodulecell-tray-mk2-seedplug-tray This 6 cell module tray for starting your seeds, designed to be strong…
This has been designed as a modular seed dryer enabling you to print and stack as many layers as you require. (Two lengths of the dovetail are included one for a stack of 5 the other for a stack of 10) The idea is there is a fan housed in…
This Fan duct is based round the AC Infinity 120mm USB fan so i can install it on my grow tent. The mounting holes are 4mm designed to have an M3 brass threaded insert heat sent into them. The whole fan duct is 205mm wide so you need to…
29mm Motor Retainer for Model rocketry. This has been designed for use with CTI (Cesaroni) motors. There are 3 different version of this retainer with different outer finishes. The screw thread is: M36-2 The test retainers i were printed…
My take on a stackable egg tray for holding quail eggs, 25 eggs per shelf. Note - the photos with eggs are of an earlier prototype the hight of the legs has since been reduced a little to make them more space efficient. Note - the legs…
Plug tray with removable modules. 30x30mm at the top and hold roughly 25ml of grow medium, 14mm drainage hole to make it easy to remove plant from module. Two versions of the holder a 3x3 (uses 4 legs) and a 4x6 (uses 5 legs), with two…
Dibbler plate designed to be used with the Charles Dowding series of seeds trays (should work with all current versions, 60, 30 and 15 cell versions) made by Containerwise. Sized to make a nice size hole for planting your seeds into. The…
This is a 3d printable lid for your Fellow Ode coffee grinders bean hopper. Print a replacement or customise your Ode with a custom color lid! I plan to add a version to accommodate bellows, but as there are multiple designs of bellows I…
So the stock rubber feet for the MK3 leaves your printer wobbling all over the place, the hard feet are great but make your printer a lot noisier. There has to be a better solution right? This is a designed to hold the stock rubber feet…
Nosecone for Estes BT-60 tubing. The nosecone has a shoulder that screw on so to accommodate a tracker or altimeter. Print instructions Category: 3D Printing
Water dispersion screen designed to work with your AeroPress to help distribute water evenly and gently onto your bed of coffee grounds. This has been specifically designed so that the AeroPress can be used in a similar way to the…
Quick little print so you can hang a Govee Thermometer using the Keyhole mount on the back in a polytunne/greenhouse or wherever you need to hang it. It has 4mm hole for string/rope for hanging. This print makes it easy to attach and…
This has been designed to turn a length of Floplast 115mm HI-Cap gutter into hanging planter for something like lettuce. The end cap is printed with no top and bottom layers with honeycomb infill at 15% to get the lattice on the end for…
Inspired by various commercially available Lame's of a similar style i have created this 3d printable disk Lame. Both sides are symmetrical so print 2 copies of your chosen design (or mix and match as you like) Hardware required: M2 X 5mm…
5:1 ratio ogive nosecone designed to fit a tube with an OD:41.6mm and ID:40.5mm. The nosecone has been split into 3 separate parts so that it can be printed on a small print bed. The nosecone is two parts with a maximum hight of 120mm…
simple slot everything together and secure with the the M3x60 bolts. Parts to print: Top x1 Intermediate screen x2 base x1 mounting bracket x1 Print Settings: Filament - PETG (or other UV resistant filament) Layer height - 0.3 Support -…
3D print designed for a 25mm NFC disk/coin snaps into place so it can be used as a plant marker. standard version uses about 1.1 grams of plastic Long version uses about 1.4 grams of plastic. I suggest printing in a UV resistant plastic,…
I have designed this to make is easy and simple to plant, plants grown in my standard and shallow module trays. Link to my module trays - https://www.prusaprinters.org/prints/71854-seedmodulecell-tray-mk2-seedplug-tray
This is a holder designed to fit inside a 1/2 size seed tray to hold 20 small Jiffy Pellets upright inside the seed tray. Print instructions Category: Outdoor & Garden
3d printable dibber for the easy planting of seedling grown in containerwise 40L module trays. It will print on its end with no support but consider using a brim for better bed adishion. I would suggest printing it with 3 perimeters and…
standard version is for use with M1.4 or M1.6 screws Second version is designed for M1.6 brass threaded inserts.
This is an avionics sled designed for PML 2.5" coupler tubing for high power rockets. It has been designed to fit inside a 160mm length of coupler tube, which is slightly longer than the standard length coupler. Desighn specs: Rails: 4mm…
I wanted to create an easy to use and set up launch pad for my model rockets using MakerBeam as a small launch rail for my low to mid power rockets. It was important for me to design the launch pad so that it is quick and easy to change…
This is a MK2 version of my original BT-60 Av bay, while it might look similar to the original this is effectively a clean sheet design. Why you might ask?: Well the 1st version worked well as a proof of concept and in flight preformed…
Protective case for your Eggtimer Quantum so that it doesn't accidentally get damaged when it's not in a rocket. This case also fit the Eggtimer WIFI Switch. Edit: I have now included the fusion 360 file incase you want to make alteration…
For convenience here are 2, 3 and 4 nozzle versions of the Revo nozzle holder.
Protective case for your Eggtimer Quark so that it doesn't accidentally get damaged when its not in a rocket. I sugest printing the 2 parts separately, that way you get a much better finish on the slot that hold the Quark and you…
This is a complete from scratch redesign of my BT-60 3d printable AV bay with the aim of making it easier to print, more reliable and toolless setup in the field. designed for used with the Eggtimer Quark flight computer (but i have…
This bracket has been designed to stop/reduce the Accur8 weather stations false triggering the rain sensor in strong wind. The bracket goes between the Accur8 weather stations plastic mounting pole and a 25.4mm (1 inch) universal weather…
Protective case for your Eggtimer Proton so that it doesn't accidentally get damaged when it's not in a rocket. Edit: I have now included the fusion 360 file, incase you want to make alteration to the design. Print instructions Category:…
This is an avionics sled designed for PML 2.5" coupler tubing for high power rockets. It has been designed to fit inside a 160mm length of coupler tube, which is slightly longer than the standard length coupler. It has been designed for…
These are all currently available results.
